Search: Posts Made By: Mranieri
Showing results 1 to 25 of 92
Search took 0.02 seconds.
Replies: 8
Views: 1,097
Posted By Mranieri

It only rings twice and hangs up...it is...

It only rings twice and hangs up...it is programmed to call twice but calls 15.
Replies: 8
Views: 1,097
Posted By Mranieri

Ok...it dialed each number 15 times..... but dial...

Ok...it dialed each number 15 times..... but dial attempts is set to 2....:wall:
Replies: 8
Views: 1,097
Posted By Mranieri

It is.... very confusing. I removed all reporting...

It is.... very confusing. I removed all reporting accept alarms and no change. As soon as an alarm engages, it calls the numbers loaded..each twice as programmed but then cycles again.

Anything...
Replies: 8
Views: 1,097
Posted By Mranieri

Thanks Ron.... I believe it is... Location 2...

Thanks Ron.... I believe it is... Location 2 shows a "4"
Replies: 8
Views: 1,097
Posted By Mranieri

Programmed my cell in GE NetworX NX8V2 but constantly calls!

I have a GE NetworX NX8V2with LCD keypad. My home was burglarized a few weeks ago (got comfortable and we stopped arming it).... anyway, I programmed the system to call my cell... however it will not...
Replies: 3
Views: 1,095
Posted By Mranieri

I found another neutral and spliced into...

I found another neutral and spliced into it......fan is now running but I think the main board relay must be bad as the fan does not turn off......
Replies: 3
Views: 1,095
Posted By Mranieri

there are two wires going to the evap fan....one...

there are two wires going to the evap fan....one is red and shows 120 volts the other is pink and shows hardly anything.......the only pink other pink I can find goes to the main board on the control...
Replies: 3
Views: 1,095
Posted By Mranieri

Jenn Aire side by side fridge evap fan replacement help

My 7 year old Jenn Air stopped working one night.......When I began to trouble shoot, I can see that the compressor is working because the lower portion of the freezer gets cold but no cold air was...
Replies: 12
Views: 8,727
Posted By Mranieri

wait...before you jump.......I had the boiler...

wait...before you jump.......I had the boiler professionally serviced a few months back and the burn tests were done so something else was wrong.......I opened up the gun to check the connections and...
Replies: 12
Views: 8,727
Posted By Mranieri

I am getting 4 flashes which obviously indicates...

I am getting 4 flashes which obviously indicates a problem. What is the typical cause of this?
Replies: 12
Views: 8,727
Posted By Mranieri

Thanks Rbeck......I just read on Beckett site how...

Thanks Rbeck......I just read on Beckett site how to run this test.......I will try tonight.

Regards
Replies: 12
Views: 8,727
Posted By Mranieri

well, I had it professionally cleaned in march...

well, I had it professionally cleaned in march and the problem went away until yesterday. My wife said there was no hot water ( indirect hot water) so I wnt to the basement and it was back on Lock...
Replies: 12
Views: 8,727
Posted By Mranieri

No, Boiler was running well until a few weeks...

No, Boiler was running well until a few weeks ago. No unusual amounts of oil being consumed.....problems just started.

My guy moved so I have to find someone I trust.
Replies: 12
Views: 8,727
Posted By Mranieri

I installed a new screen, filter and nozzle this...

I installed a new screen, filter and nozzle this year but I did not vacuum it out.
Replies: 12
Views: 8,727
Posted By Mranieri

5 year old Beckett NX oil burner locking out every two days

Five years ago, a plumber friend of mine and myself installed a Veismann Boiler with a Beckett NX gun. It has performed flawlessly running 86% efficient and saving me a ton of money in oil compared...
Replies: 12
Views: 11,049
Posted By Mranieri

I was planning on using screws countersunk and...

I was planning on using screws countersunk and then filled to finish. The leverage of someone pulling on the handrail will definitely loosen up nails. Thanks
Replies: 12
Views: 11,049
Posted By Mranieri

Thanks George, that makes sense. I figure a 3"...

Thanks George, that makes sense. I figure a 3" decking screw would do the trick with a little glue so the spindles don't spin. I appreciate all the advise.
Replies: 12
Views: 11,049
Posted By Mranieri

I was thinking of using dowels and glue but it...

I was thinking of using dowels and glue but it might be difficult ensuring that each spindle is drilled perfect.

I don't think just a few finish nails would suffice. Might be a little to...
Replies: 12
Views: 11,049
Posted By Mranieri

thanks guys. 4" spacing...got it! I realize...

thanks guys. 4" spacing...got it!

I realize that the bulk of the railing strength will come from the post but what is the best way to secure the balusters to the shoe?
Replies: 12
Views: 11,049
Posted By Mranieri

Help installing Balusters and handrail

Hi,

I am about to tackle the staircase in my home but have a few questions for you guys and gals.

The stair case is somewhat narrow as it is a very old home. the original railing was removed...
Replies: 19
Views: 8,994
Posted By Mranieri

My Mistake, I actually have the wireless card not...

My Mistake, I actually have the wireless card not the RF keypad so after following Ron's direction, I was able to delete and relearn the new sensor. Everything looks good.

Thanks for all your...
Replies: 19
Views: 8,994
Posted By Mranieri

I have the installer code, I just do not know how...

I have the installer code, I just do not know how to delete he old sensor.

PLease explain..thanks in advance.
Replies: 19
Views: 8,994
Posted By Mranieri

I have the new motion sensor.....how do I replace...

I have the new motion sensor.....how do I replace the defective one already programmed with the new one??
Replies: 19
Views: 8,994
Posted By Mranieri

I have the NX148E. I am fairly certain the...

I have the NX148E.

I am fairly certain the motion is bad. While switching batteries, it would intermittantly show fault as well as low batteries then clear the fault and show ready. This lasted...
Replies: 19
Views: 8,994
Posted By Mranieri

How to delete a wireless zone?

i think my motion sensor went bad and dont have another available. How do you delete a zone from the wireless module? I will get another motion sensor and add it later but the beeping is driving me...
Showing results 1 to 25 of 92
 


 
Forum Jump