Search: Posts Made By: Ham
Showing results 1 to 25 of 41
Search took 0.01 seconds.
Replies: 2
Views: 1,512
Posted By Ham

Shindaiwa Weed Trimmer.

I am trying to rebuild a Shindaiwa T-231 weed trimmer and I accidentally broke one of the fins on the flywheel while disassembling it. Will that make the flywheel be off balanced?
Replies: 13
Views: 6,082
Posted By Ham

Do the Tecumseh carbs have the same setup? Mine...

Do the Tecumseh carbs have the same setup? Mine will prime but will not stay running.
Replies: 7
Views: 9,119
Posted By Ham

What's the purpose of this skid plate? The skid...

What's the purpose of this skid plate? The skid plate on my mower deck is only about a foot and a half long and basically goes under the shute opening. I had to remove mine because it was bent and...
Replies: 32
Views: 51,053
Posted By Ham

I just got a used Craftsman 42" cut mower that...

I just got a used Craftsman 42" cut mower that was doing the same thing. The right side was cutting higher than the left side.
I fought with the adjustments on it for awhile until I got to looking...
Replies: 7
Views: 1,354
Posted By Ham

What is graphite? If not oil and grease what...

What is graphite? If not oil and grease what then? I have had this similar problem where it would not engage and I had to take it apart and clean it up. I used oil but it did it the next season.
Replies: 1
Views: 1,285
Posted By Ham

Generator Assembly

I am working on a Devilbiss GB5000 generator with a B&S 10.0 H.P. engine and I am trying to get the rotator assembly off to change the oil seal. I found a diagram of the machine and it shows that the...
Replies: 9
Views: 1,632
Posted By Ham

Truck Runs

I put a set of new plugs on the truck and it started right up. The old one were fouled badly. I was thinking that it was either the distributor or the carb, that's why I didn't try the plugs first....
Replies: 9
Views: 1,632
Posted By Ham

Update on Truck

I decided to pull the fuel filter off the truck and when I emptied it into a cup it was nothing but rusty fuel that came out the inlet side. Now, even though the fuel pump is still working, I think...
Replies: 9
Views: 1,632
Posted By Ham

Update on Truck

I decided to pull the fuel filter off the truck and when I emptied it into a cup it was nothing but rusty fuel that came out the inlet side. Now, even though the fuel pump is still working, I think...
Replies: 9
Views: 1,632
Posted By Ham

Let me tell what happened with the truck and...

Let me tell what happened with the truck and maybe it will be clearer. I drove the truck that morning and it ran great, but after setting for about 4 or 5 hours it would not start. There was no extra...
Replies: 9
Views: 1,632
Posted By Ham

What's the best way to check for leaks? Let me...

What's the best way to check for leaks? Let me tell what happened with the truck and maybe it will be clearer. I drove the truck that morning and it ran great, but after setting for about 4 or 5...
Replies: 9
Views: 1,632
Posted By Ham

'94 Isuzu Truck

I have a '94 Isuzu pickup with a 2.3 litre engine that will only run when I have the breather off. It's hard to start but once it starts it will run rough. It will cough back through the carb and...
Replies: 9
Views: 1,632
Posted By Ham

'94 Isuzu Truck

I have a '94 Isuzu pickup with a 2.3 litre engine that will only run when I have the breather off. It's hard to start but once it starts it will run rough. It will cough back through the carb and...
Replies: 1
Views: 611
Posted By Ham

Marking a Thread

Is there anyway to mark a thread on this forum that you can go back to for future references? There are a few that I would like to keep but don't want to have to go back through all the threads to...
Replies: 32
Views: 2,748
Posted By Ham

Won't this cause shaving. Or are they big enough...

Won't this cause shaving. Or are they big enough to matter?
Replies: 4
Views: 1,748
Posted By Ham

I looked at the adjustments on the weedeater and...

I looked at the adjustments on the weedeater and there is no plastic limiters on it. There is 2 knobs that are splined and will take a special socket. Any ideas where I can get this socket?
Replies: 4
Views: 1,748
Posted By Ham

Thanks, I'll try it this evening.

Thanks, I'll try it this evening.
Replies: 4
Views: 1,748
Posted By Ham

Weedeater Won't Run

I have a Poulan Pro Model # PPB100 711820 that's mabye a year old. It will not stay running long. I will choke it and pull then switch it to half choke and it will run for a few seconds and that's...
Replies: 1
Views: 918
Posted By Ham

Starter Repair

Does anyone know if there is a starter rebuild kit for model #OHV130 206820B or do you have to buy a new starter?
Replies: 4
Views: 1,176
Posted By Ham

Proper Way to Troubleshoot

What's the best way to learn how to troubleshoot an engine and not be just a parts changer? I hate to change one part and it be something totally different.
Replies: 4
Views: 830
Posted By Ham

Will the twin cylinder engine fit under the hood...

Will the twin cylinder engine fit under the hood of the mower?
Replies: 5
Views: 1,099
Posted By Ham

Engine #'s

Hey puey,
Any thing on these #'s yet? The model # on the 13 hp - OHV130 206820B and the 17 hp - OHV 175 204807B.
Replies: 5
Views: 1,099
Posted By Ham

It ain't Monday but here it is. The model # on...

It ain't Monday but here it is. The model # on the 13 hp - OHV130 206820B and the 17 hp - OHV 175 204807B.
Replies: 5
Views: 1,099
Posted By Ham

I will try to post the #'s Monday.

I will try to post the #'s Monday.
Replies: 5
Views: 1,099
Posted By Ham

Starter & Coil

Will a starter and coil from a 17 hp Tecumseh fit a 13 hp Tec.?
Showing results 1 to 25 of 41
 


 
Forum Jump