Search: Posts Made By: Bill Puter
Showing results 1 to 25 of 28
Search took 0.02 seconds.
Replies: 2
Views: 2,292
Posted By Bill Puter

Find the model number speed make on the chip and...

Find the model number speed make on the chip and do a search for a mother board that is compatible.
07-28-06, 06:36 AM
Replies: 2
Views: 1,966
Posted By Bill Puter

Just break them up. Chip them away underneath the...

Just break them up. Chip them away underneath the cabinets enought to fit a new tile underneath so the edge of your new cut tile won't show.
Forum: Water Heaters
07-27-06, 07:46 PM
Replies: 9
Views: 4,997
Posted By Bill Puter

Glade to hear you got it fixed. Sorry for not...

Glade to hear you got it fixed. Sorry for not repling sooner, Work has had me out all night this week.

This fourm is great for do it yourselfers and the non mechanically inclined.

I have been...
Forum: Water Heaters
07-24-06, 08:52 PM
Replies: 9
Views: 4,997
Posted By Bill Puter

Well That is strange. We may need to do some...

Well That is strange. We may need to do some diagnostic work first before replaceing parts. Are you sure you are getting electric to the unit it self? You can test the voltage at the thermostat. Did...
Forum: Water Heaters
07-24-06, 07:21 AM
Replies: 9
Views: 4,997
Posted By Bill Puter

Turn the power to the heater first. Usually...

Turn the power to the heater first.

Usually the top and bottom elements each have their own thermostat and are wired so that only one element comes on at a time. Normally the upper thermostat...
Forum: Water Heaters
07-23-06, 08:26 PM
Replies: 9
Views: 4,997
Posted By Bill Puter

There is a breaker on most water heaters so check...

There is a breaker on most water heaters so check that first. Usually a little red button under a panel that needs to be unscrewed. Warning there is a risk of being shocked so shut the breaker off at...
Replies: 1
Views: 1,100
Posted By Bill Puter

Its sould like its time to replace the flaper. Do...

Its sould like its time to replace the flaper. Do you ever hear water running in the toilet? Or does the toilet refill from time to time with out any use? These are all signs of a bad flapper. Also...
Replies: 2
Views: 769
Posted By Bill Puter

Ok We need to elimate problems one by...

Ok

We need to elimate problems one by one. Make sure you have a good tank of fresh fuel and a good line to feed from that tank. Pump the primer bulb untill tight but don't over do it.

If...
07-06-06, 08:03 PM
Replies: 12
Views: 5,386
Posted By Bill Puter

I'm sorry I didn't read good enough. Are the...

I'm sorry I didn't read good enough. Are the hinges attached with wood screws? If so I would remove them and replace with bolts that go all the way thru to the other side of the frame.

Just drill...
07-06-06, 06:40 AM
Replies: 12
Views: 5,386
Posted By Bill Puter

At this point I would use both turn buckel and a...

At this point I would use both turn buckel and a support 2x4. Yes run the flush with the frame of the gate. Use pressure treated wood reguardless of what they have used.

In the pictures the gate...
07-05-06, 06:50 PM
Replies: 12
Views: 5,386
Posted By Bill Puter

You should run a center board from the left top...

You should run a center board from the left top corner to the bottom right corner. This will releave some pressure from your fence boards they look like there holding it all together.

While...
Replies: 2
Views: 1,849
Posted By Bill Puter

That sure sounds like the lower unit oil. ...

That sure sounds like the lower unit oil.

Here is the way to check. There are two drain plugs on the lower end. Remove the bottom drain plug and let a little oil drain out ( Catch the oil in a...
Replies: 1
Views: 1,001
Posted By Bill Puter

You can get what is known as a nohub connector...

You can get what is known as a nohub connector that will reduce from 4in to 2in. Just check your local hardwear store.
Replies: 3
Views: 7,676
Posted By Bill Puter

You will need a cassette deck and a cd player....

You will need a cassette deck and a cd player. Hook them up to am amp. Then go out of the amp and into the tape deck. Unless you have a home stereo were all the components are one unit. Then all you...
Replies: 8
Views: 3,624
Posted By Bill Puter

Sound like you may have somethign there. If you...

Sound like you may have somethign there. If you would like to talk to experts on johnson/evenrude check this forum out.

http://www.iboats.com/bbboard/bbBoard.cgi
Replies: 8
Views: 3,624
Posted By Bill Puter

The fuel pump works off of a vacuum so I doubt it...

The fuel pump works off of a vacuum so I doubt it can be causing to much pressure. How hard are you pumping the primer bulb? It does not require alot of pumping just untill it get hard.
Replies: 8
Views: 3,624
Posted By Bill Puter

It maybe time to look into the fuel pump and...

It maybe time to look into the fuel pump and check to make sure those needles are good. The needles are what the float pushes up on to stop the flow of gas when the bowl is full.

It sounds like...
Replies: 6
Views: 1,292
Posted By Bill Puter

Sounds like an air problem. Check the filter and...

Sounds like an air problem. Check the filter and carberator for any debris that might hinder the air flow. Clean the sparkplug also.
Replies: 17
Views: 5,632
Posted By Bill Puter

Well it will take you at least a day to tear off...

Well it will take you at least a day to tear off and replace the rotton wood. You should cut out the old boards and replace them with plywood not a full sheet just the bad sections. Make sure you cut...
06-08-06, 06:37 AM
Replies: 5
Views: 1,188
Posted By Bill Puter

Try an oxygen cleaner like oxyclean you can pick...

Try an oxygen cleaner like oxyclean you can pick this up in your local grocery story.
06-08-06, 06:30 AM
Replies: 7
Views: 1,206
Posted By Bill Puter

I was at a hardware store today and saw a hand...

I was at a hardware store today and saw a hand operated texture sprayer. It did three types of texture Orange peel, Pop corn and splater. It was about 40 bucks but this place is always high on there...
06-06-06, 01:45 PM
Replies: 1
Views: 1,015
Posted By Bill Puter

I would sand a little corner first to see what...

I would sand a little corner first to see what the wood looks like underneath the paint. If you like the wood, the floor machine will work fine you might have to clean the sand paper from time to...
06-05-06, 06:58 AM
Replies: 7
Views: 45,932
Posted By Bill Puter

You should cover the concrete up.

You should cover the concrete up.
06-01-06, 08:13 PM
Replies: 2
Views: 5,792
Posted By Bill Puter

RE Hey DIY'ers and pros.

Just back fill with dirt untill its to the right size. Then concrete the post in. If you don't use concrete the post will not stay plumb. They also recommend that you use some rock or gravel at the...
06-01-06, 07:56 PM
Replies: 1
Views: 2,152
Posted By Bill Puter

Re Chain Link Gate Problems

To reinforce the gate you could try a turnbuckle. It connects at the top corner and the opposite bottom corner of the gate and tighten.

As for the gate draging make sure the post it connects to is...
Showing results 1 to 25 of 28
 


 
Forum Jump