Search: Posts Made By: strider380
Showing results 1 to 25 of 167
Search took 0.02 seconds.
Replies: 7
Views: 6,127
Posted By strider380

Thanks everyone. I pulled the valve out and got...

Thanks everyone. I pulled the valve out and got it moving and the pressure has come back! But the machine does not idle up when you pull the trigger. Resulting in low idle and lower then normal...
Replies: 7
Views: 6,127
Posted By strider380

This is what the pump looks like. Never saw one...

This is what the pump looks like. Never saw one like this. Its pretty impressive to watch when running! Any advise on where to start?
...
Replies: 7
Views: 6,127
Posted By strider380

Pressure washer builds pressure for a second then loses it

Hello, i have a Dewalt pressure washer. Ill have to get the model number later. I dont know the history but it starts and runs great. The water pressure only kicks in for about one second though,...
Replies: 10
Views: 10,127
Posted By strider380

Is it normal tho that when i spray carb cleaner...

Is it normal tho that when i spray carb cleaner on the trottle shaft of the carb, the motor bogs down? I immediatly thought that was a problem. Ive always been taught to spray carbs on jeeps to find...
Replies: 10
Views: 10,127
Posted By strider380

Yes it has a needle in the side for idle mixture....

Yes it has a needle in the side for idle mixture. The main jet screws into the bottom of the bowl and goes straight up. The jet has a hole going straight through horizontally. Then a much smaller...
Replies: 10
Views: 10,127
Posted By strider380

Adjusting the mixture screw dosnt seem to make...

Adjusting the mixture screw dosnt seem to make the surging go away. The main jet is clean clean clean. I ran a wire through it for a while. Is it possible the linkage on the govenor/throttle has to...
Replies: 10
Views: 10,127
Posted By strider380

Generator throttle surging... governor?

I have an old generator that has a techumseh 10hp motor. I cleaned the carb and put new gaskets in and the generaror came back to life. Except it is surging non stop and occasional back fire. I did...
Replies: 3
Views: 481
Posted By strider380

Now that you mention that, it seems to idle down...

Now that you mention that, it seems to idle down and then not idle up when I pull the trigger. Any instant go to when that happens? Ill get the model number tomorrow.
Replies: 3
Views: 481
Posted By strider380

Dewalt pressure washer idles too low when warm

Anyone know what would cause this? The pressure washer works great when started, but after a minute or two, the engine drops in Idle and the pressure goes down. I havn't been able to find any...
Replies: 4
Views: 2,011
Posted By strider380

Ok great! Thanks for the advice i'm sold!

Ok great! Thanks for the advice i'm sold!
Replies: 4
Views: 2,011
Posted By strider380

refinishing barnboard countertops

Hi everyone I have an old farmhouse I spent years returning back to its original style. After living in it for several years since the restoration, I am trying to perfect the things I did wrong. ...
Replies: 2
Views: 730
Posted By strider380

recessed cans thermal sensor

Hello I put up (2) 4 inch IC recessed cans over a bathroom vanity. I installed them buy cutting up the floor boards in the attic above the bathroom, putting in new constuction cans, then...
Replies: 3
Views: 4,339
Posted By strider380

Ok, so if I don't have the hose, i can do the...

Ok, so if I don't have the hose, i can do the pressure/vaccum test through the spark plug hole? Also, is bailey's a quality place to get parts like this?
Replies: 3
Views: 4,339
Posted By strider380

Advice on crank seals in a chainsaw?

I once scored the piston, ring and jug on my husky 55. I put on a new kit and it still didn't run quite right. No power and didn't idle. Then it got stolen :) Shortly after I found out that I...
08-28-12, 07:40 PM
Replies: 2
Views: 1,725
Posted By strider380

Use a cieling bath vent fan in wall?

Hello all, I am remodeling my bathroom and deciding on the vent fan. Its on a third floor and the only option is to vent the bath fan straight out the wall. When we run into this, I pick up a...
Replies: 7
Views: 1,057
Posted By strider380

and oops. its a 03 Toyota corolla. is it very...

and oops. its a 03 Toyota corolla. is it very possible that the throw out bearing or clutch plate could have gone at 90,000 miles? the one on my civic made it to 160,000 and i only changed it...
Replies: 7
Views: 1,057
Posted By strider380

Can anyone help me diagnose this strange grinding noise??

I picked up my sisters car to bring to my house for a complete tune up. Once i got it home, I changed the air filter, cleaned off a ton of corrosion on the battery, and took off drivers front wheel...
09-21-10, 08:22 AM
Replies: 3
Views: 2,648
Posted By strider380

Splice sub panel feeders in PVC LB fitting

I am running #2 AL feeders to a small detached apartment. It comes from the main panel in the main house as SER cable. Where it exits the house it goes underground via 2" pvc with appropriate wire....
Replies: 7
Views: 2,824
Posted By strider380

Ooops, I'm sorry. Yea it is a factory alarm. ...

Ooops, I'm sorry. Yea it is a factory alarm. How much would the dealer charge to scan my alarm? Or is it a freebie?
Replies: 7
Views: 2,824
Posted By strider380

Can I just pull a fuse and disconnect it?

Can I just pull a fuse and disconnect it?
Replies: 4
Views: 1,074
Posted By strider380

Ok...I went through everything. Tried some known...

Ok...I went through everything. Tried some known working ram, disconnected and reconnected the motherboard, disconnected all the ide devices, power cycled the computer, Checked that the fan is...
Replies: 7
Views: 2,824
Posted By strider380

99 Honda Civic alarm doing random things

Somethings definitly wrong with my alarm system. Its a 99 Honda civic ex. It started probably 6 days ago. The remote on my keychain would no longer unlock the door and disable the alarm. I...
Replies: 4
Views: 1,074
Posted By strider380

Computer won't turn on?

My friends all think I am good at fixing computers, but really I just reformat them and give them back. I've probably done it a couple dozen times until this time...This is a dell dimension 2400. ...
Replies: 2
Views: 2,688
Posted By strider380

Husky chainsaw only runs with choke on

Long story short...

My Husky 55 rancher ran great for 5 years until I burnt the top end on my chainsaw one lovely evening. I put on a new ring piston and jug, but it wouldn't run right. Have...
Replies: 4
Views: 877
Posted By strider380

hmmm...thats some good advice. This is actually...

hmmm...thats some good advice. This is actually the OEM setup. Its original to the car. The plastic lines are straight lengths and the rubber hose that flattens is a U shape. They are starting to...
Showing results 1 to 25 of 167
 


 
Forum Jump