Search: Posts Made By: whozat
Showing results 1 to 14 of 14
Search took 0.01 seconds.
02-11-09, 08:11 PM
Replies: 11
Views: 3,423
Posted By whozat

Sorry, EC. I was under the house again. ...

Sorry, EC. I was under the house again.

I'll buy the ampmeter AND the baseboards tomorrow. Altogether, it'll cost less than $300 and I'll keep them installed as a backup for whatever furnace I...
02-11-09, 07:44 PM
Replies: 11
Views: 3,423
Posted By whozat

Alright...one more night like this and I'm...

Alright...one more night like this and I'm putting in friggin 220 electric baseboards until Spring.

I'm not getting any multimeter readings from either motor. It was my intention to replace this...
02-11-09, 07:25 PM
Replies: 11
Views: 3,423
Posted By whozat

$#!T. OK, the blower door is already off and...

$#!T.

OK, the blower door is already off and I've already taped the interlock switch so I could see if anything obvious was happening. I didn't hear anything out of the ordinary when it shut off,...
02-11-09, 06:59 PM
Replies: 11
Views: 3,423
Posted By whozat

It's not the breaker. I just got back from...

It's not the breaker. I just got back from Menard's with a new one. Something's causing it to trip. I think I've got a multimeter around here somewhere.

Where should I be looking for a short or...
02-11-09, 06:46 PM
Replies: 11
Views: 3,423
Posted By whozat

Goodman GMP075 tripping brakers!! Help!

My GMP075 is causing the breaker to the furnace to trip. When the breaker's reset, the furnace will act as normal (draft fan OK,Ignitor OK, gas valve OK, Circulation fan OK) but will only run for...
02-04-09, 08:54 AM
Replies: 7
Views: 943
Posted By whozat

I got the furnace working but I intend on...

I got the furnace working but I intend on replacing it this Spring. This one will likely require a new heat exchanger but, considering the cost, I may as well replace the whole furnace instead. I...
02-04-09, 08:50 AM
Replies: 6
Views: 2,129
Posted By whozat

After a sleepless night waiting to see if the...

After a sleepless night waiting to see if the furnace acted up again, I can report it worked like a charm. I had a dead limit switch and one dead rollout switch. After replacing them (and a cursory...
02-02-09, 07:22 PM
Replies: 7
Views: 943
Posted By whozat

Grady!! You 'da man!! I got it. Thanks!

Grady!! You 'da man!!

I got it. Thanks!
02-02-09, 06:06 PM
Replies: 7
Views: 943
Posted By whozat

Thanks again. I would think Goodman made a repair...

Thanks again. I would think Goodman made a repair manual for this thing but I'd appreciate something with an in-depth wiring schematic.

If the installation manual has that, could I bother you to...
02-02-09, 06:03 PM
Replies: 6
Views: 2,129
Posted By whozat

Thanks, Grady! Now all I have to do is FIND a...

Thanks, Grady!
Now all I have to do is FIND a limit switch in South Bend, IN.

By the way, you wouldn't happen to know the correct part number for it? The numbers on mine are so light, they can't...
02-02-09, 06:00 PM
Replies: 7
Views: 2,779
Posted By whozat

I'm following this thread with great interest...

I'm following this thread with great interest because I'm having the same problem. 4 flashes, circulation fan running constantly but no ignition, no combustion gas (exhaust) blower, nada. Just the...
02-02-09, 05:36 PM
Replies: 7
Views: 943
Posted By whozat

I need a GMP075 manual: Anybody have 1?

Is there a GMP075 manual available online or does one have a copy they'd like to get rid of?

Please respond ASAP. Thanks!
02-02-09, 05:29 PM
Replies: 6
Views: 2,129
Posted By whozat

Unhappy Goodman GMP075-3 problem: HELP!!!

My GMP075-3 was blowing fuses on the mother board and I traced the problem to the limit switch behind the gas valve. Now the furnace's cold air fan comes on but nothing else happens. The ignition...
01-26-08, 11:31 AM
Replies: 3
Views: 2,591
Posted By whozat

Sunbeam fireplace

I don't know if you've resolved your problem but I just finished fixing my Sunbeam fireplace. It was doing the same thing yours was and here's what I did.

On the top of the heating element...
Showing results 1 to 14 of 14


 
Forum Jump