Search: Posts Made By: 28yrsgm
Showing results 1 to 15 of 15
Search took 0.01 seconds.
Replies: 8
Views: 6,139
Posted By 28yrsgm

sorry guys........didn't notice this was an old...

sorry guys........didn't notice this was an old post. So what was the solution?
Replies: 8
Views: 6,139
Posted By 28yrsgm

I would look again at the input and third sprag...

I would look again at the input and third sprag assemblies. When assembled and placed on the input sun gear, hold the sun gear in your left hand with the sprags facing up. You should be able to turn...
Replies: 8
Views: 6,139
Posted By 28yrsgm

Looking in a 1998 GM transmission manual, it...

Looking in a 1998 GM transmission manual, it shows four checkballs in the channel plate and six in the valve body.
Replies: 3
Views: 1,463
Posted By 28yrsgm

If you disconnect the switch harness under the...

If you disconnect the switch harness under the dash and they still run you have a shorted motor. If they quit running you have a bad switch.
Replies: 8
Views: 5,690
Posted By 28yrsgm

A no cost way to verify cause of your...

A no cost way to verify cause of your misfire..........since you know what cylinderws are misfiring, at 2200 pull the coil to plug wire off #5 spark plug, or an old trick was to put a piece of rubber...
Replies: 4
Views: 889
Posted By 28yrsgm

I have come across several of these engines with...

I have come across several of these engines with a bent pushrod or two. Never could find a definite cause other than overrevving, esp. with a standard trans. Never had any come back with any other...
Replies: 12
Views: 1,378
Posted By 28yrsgm

If the noise was not there before pulling the...

If the noise was not there before pulling the intake, then there is a good chance something metallic fell into an intake port while the intake was off. If the knock sounds heavy, like hitting an iron...
Replies: 5
Views: 1,072
Posted By 28yrsgm

I still say check the front stabilizer bushings....

I still say check the front stabilizer bushings. RJ says he hears a low pitched SCRUNCHING sound at lower temperatures and only while moving. I bet you hear it going over a speed bump or in/out of a...
Replies: 5
Views: 1,072
Posted By 28yrsgm

sounjds like stabilizer bushings are worn and...

sounjds like stabilizer bushings are worn and dried up.
Replies: 6
Views: 2,029
Posted By 28yrsgm

swap #3 and # 1 plug wires. If your miss moves to...

swap #3 and # 1 plug wires. If your miss moves to #1 you found the problem. Also check the terminals on the coil that serves #3 to see if it is corroded. Normally, and I hate to say this, but when a...
Replies: 7
Views: 15,388
Posted By 28yrsgm

Making a slight right turn puts weight on the...

Making a slight right turn puts weight on the left front bearing and left turns tranfer weight to the right side. A fairly sharp right turn under even slight acceleration will cause a bad right outer...
Replies: 3
Views: 1,366
Posted By 28yrsgm

Hey Morph, how many miles have you put on in two...

Hey Morph, how many miles have you put on in two years? Even my wife knows the noise goes away when you apply the brakes! Pull a front wheel and check the pads. Betcha a wooden nickel the wear...
Replies: 9
Views: 1,220
Posted By 28yrsgm

I'm gonna stick my neck out here and advise...

I'm gonna stick my neck out here and advise calipers be replaced. The brake hoses certainly could cause this, but they have been replaced.
BTW ASE, Ford has used non-metallic caliper pistons in the...
Replies: 8
Views: 3,915
Posted By 28yrsgm

Hey kennn............has your belt noise gone?

Hey kennn............has your belt noise gone?
Replies: 2
Views: 1,194
Posted By 28yrsgm

An 89 Skyhawk would still have the governor...

An 89 Skyhawk would still have the governor controlled transaxle. Check the cable that runs from the shifter to the trans. sound like either the cable has broken inside the casing, or the cable has...
Showing results 1 to 15 of 15


 
Forum Jump