Search: Posts Made By: 38racing
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Replies: 42
Views: 3,702
Posted By 38racing

In some cases the brass seat needs to be replaced...

In some cases the brass seat needs to be replaced as well. Have you done a compression check to make sure valves are ok?
Replies: 9
Views: 30,773
Posted By 38racing

there is also a static governor adjustment to do...

there is also a static governor adjustment to do whenever carb has been removed and put back on. Common to have to do that to stop surge on briggs and had it on a tecumseh once as well
Replies: 6
Views: 5,982
Posted By 38racing

Have you ever had the carb off and possible got...

Have you ever had the carb off and possible got the linkage wrong. Can't put my hands on it right now but I have seen the adjustment for it . Might be in a briggs manual. Might be as simple as an...
Replies: 3
Views: 904
Posted By 38racing

probably the carb needs cleaned and I just had...

probably the carb needs cleaned and I just had one of those where the primer failed to work because it needed a new bowl gasket to make a proper seal
Replies: 7
Views: 4,660
Posted By 38racing

what's interesting about that bearing is that the...

what's interesting about that bearing is that the OEM bearing inner race may be have a keyway. That means that you should not get the situation where the bearing seizes and the shaft turns inside the...
Replies: 10
Views: 18,130
Posted By 38racing

I see 2 murray/noma belts for blower augers which...

I see 2 murray/noma belts for blower augers which are close in size.
3526 is 30 1/8 and 3887 is 30 7/8. Do you know which you got?
edit: however I just looked at an ipl for a 620301x4c and looks...
Replies: 10
Views: 18,130
Posted By 38racing

this long link may pop up a pdf for a typical...

this long link may pop up a pdf for a typical murray small blower...
Replies: 8
Views: 3,611
Posted By 38racing

Gasket above the bottom bowl? Are you referring...

Gasket above the bottom bowl? Are you referring to the bowl to carb gasket or the one for the bolt/jet? Is your bolt/jet gasket inside the bowl or outside? Should be outside , between bowl and head...
Replies: 31
Views: 32,982
Posted By 38racing

Since you said the governor spring was off and...

Since you said the governor spring was off and put back on, have you tried holding the governor lever fixed and seeing if the surging stops or the engine stalls. Still puzzled about effect of choke....
Replies: 5
Views: 1,407
Posted By 38racing

can you see that the impeller is still turning...

can you see that the impeller is still turning when the augers push the snow back? If not then maybe box is filling with snow and the augers bogg and stall the engine. The impeller is pinned to the...
Replies: 5
Views: 4,692
Posted By 38racing

could also be a rubber disc drive

could also be a rubber disc drive
Replies: 21
Views: 37,398
Posted By 38racing

if you have a generator that you don't start at...

if you have a generator that you don't start at least monthly and let it run awhile then you'll have one that won't run when you need it because the carb will be all gummed up
Replies: 21
Views: 37,398
Posted By 38racing

why wouldn't the engine have a charging stator...

why wouldn't the engine have a charging stator like a riding mower?
Replies: 6
Views: 6,165
Posted By 38racing

I had same issue when taking a friend's apart...

I had same issue when taking a friend's apart after he had it apart. I thought he had the brushes wrong. I thought I had found something that showed them properly . I'll look around for it.
11-12-12, 03:55 PM
Replies: 2
Views: 951
Posted By 38racing

It's my understanding that when the gen is...

It's my understanding that when the gen is neutral bonded to frame rather than 'floating' then the transfer switch must break the neutral in addition to the hots.
11-12-12, 03:47 PM
Replies: 2
Views: 951
Posted By 38racing

If the 3 prong is 240V then it provides 240 volt...

If the 3 prong is 240V then it provides 240 volt only (I have that on a lincoln welder/generator). The receptacle has red, black, and ground , no neutral , hence no 120v from that plug. It's not...
Replies: 35
Views: 15,916
Posted By 38racing

you might find that it's much like this one ...

you might find that it's much like this one
Outdoor Distributors - Lawn Mower Parts...
Replies: 22
Views: 8,750
Posted By 38racing

That makes sense 38racing. But the solenoid, if...

That makes sense 38racing. But the solenoid, if not working properly can cause his problem if the fuel is not allowed to enter the main jet from the float bowl.

I don't think so , because if the...
Replies: 3
Views: 2,766
Posted By 38racing

check that all belt guides are in place

check that all belt guides are in place
Replies: 22
Views: 8,750
Posted By 38racing

quote The purpose of it is to prevent a backfire...

quote The purpose of it is to prevent a backfire from going back into the fuel tank. Not all engines have them.
But if it isn't opening fuel won't get into the float bowl. endquote

That's not my...
Replies: 5
Views: 1,547
Posted By 38racing

I'm don't think the 4 bolt has those small...

I'm don't think the 4 bolt has those small springs, just the 3 bolt.
Replies: 2
Views: 1,302
Posted By 38racing

briggs may still offer the dual shaft engine as...

briggs may still offer the dual shaft engine as they are used on tillers. Someone on a forum somewhere had one which I think was new. There are some blowers that drive both wheels and auger off a...
Showing results 1 to 25 of 200
 


 
Forum Jump