Search: Posts Made By: tea3803
Showing results 1 to 25 of 129
Search took 0.09 seconds.
Replies: 10
Views: 2,628
Posted By tea3803

Ok the points are set to .018" and the new coil...

Ok the points are set to .018" and the new coil is in. She cranked for about 4 seconds and now purrs like the baby she is. Thank all of you so much for the help and patience with this problem.
...
Replies: 10
Views: 2,628
Posted By tea3803

The coil looks like the type that was on cars...

The coil looks like the type that was on cars when I could still work on them. Positive side to ignition switch, negative side to condensor and points and of course the tower to the plug. No...
Replies: 10
Views: 2,628
Posted By tea3803

No idea what wire would be the kill wire. Sorry

No idea what wire would be the kill wire. Sorry
Replies: 10
Views: 2,628
Posted By tea3803

No cap and rotor. The wire to the plug comes...

No cap and rotor. The wire to the plug comes from a coil type device.
Replies: 10
Views: 2,628
Posted By tea3803

1974 Allis-Chalmers 710

The old iron has taken another dump.

While cutting the yard it just stopped. Chugged down to nothing. Not a lock up type stop. Checked everything I could think of getting fuel, fresh fuel,...
Replies: 1
Views: 2,258
Posted By tea3803

Ariens Series 935

Hi

Had this machine for quite sometime (Ariens Series 935, YT12) and now I have a couple problems. It has the Hydro Rear Drive so this is the confusing part to me I guess.

1. Cutting short...
Replies: 4
Views: 854
Posted By tea3803

Found more information on this. He last used it...

Found more information on this. He last used it in May of 2004. It sat in his carport shed through the winter. This shed has his gas water heater in it and from my thinking it would not have...
Replies: 4
Views: 854
Posted By tea3803

Small Sears Pressure Washer

A neighbor of mine has one of those $200 Sears gas engine pressure washers and it doesn't allow water to flow through the gun before start-up nor does it after start-up. Reading, the manual says...
Replies: 7
Views: 1,426
Posted By tea3803

Plenum rated Cat 5 ... for running it in duct...

Plenum rated Cat 5 ... for running it in duct work.

Another place to snake it is through the same openings your telephone wire runs. In a three story there is usually more than one jack per floor!
Replies: 5
Views: 1,737
Posted By tea3803

Puey, were you able to find anything?

Puey, were you able to find anything?
Replies: 3
Views: 931
Posted By tea3803

Around here the landscapers/yard men seem to be...

Around here the landscapers/yard men seem to be on Grasshoppers. Even this little town has a Grasshopper dealer. From looking to my neighbors yard, they have a service, it cuts very well and is...
Replies: 5
Views: 1,737
Posted By tea3803

For parts purposes I use 935026 as a model...

For parts purposes I use 935026 as a model number. Its the Ariens YT1235 machine with a Kohler 12.5 hp engine.
Replies: 5
Views: 1,737
Posted By tea3803

Airens YT12 Riding Mower

This unit runs and starts just fine. The problem is the steering. It is very sloppy. Looking at the base of the steering column at the main steering gear I can turn it past six teeth before the...
Replies: 37
Views: 1,143
Posted By tea3803

Fcc

The 56k number is just a misnomer. The FCC limits the throughput to either 52 or 53k ... can't remember offhand ... so saying 56k is just what the modem is cabable of. Nowhere no how will anyone...
08-07-04, 05:54 AM
Replies: 2
Views: 18,061
Posted By tea3803

Is this it?

Try this link out if its not it let me know.



http://www.diynet.com/diy/diy_kits/article/0,2019,DIY_13787_2581856,00.html
Replies: 11
Views: 2,393
Posted By tea3803

$73.63 later ...

Well fixed again, I was missing a huge nut (1 1/8") from the top of the main spindle shaft. It was always noisy but it got worse and thats when I found all this. So along with the nut, a couple...
Replies: 4
Views: 1,837
Posted By tea3803

Did you try squirting a little fuel into the plug...

Did you try squirting a little fuel into the plug hole then reinsert the plug and try to start it? If it starts you have a fuel flow problem. If it doesn't I would clean the carb regardless of how...
Replies: 11
Views: 2,393
Posted By tea3803

Yep

That was my next step. I was hoping to get something off the web. Thanks though for the reply.
Replies: 11
Views: 2,393
Posted By tea3803

When it rains it pours

Okay so the problems come in threes right?

Started getting this god awful noise from the mower deck when the blades were engaged. Checked the spindles and the pulley shafts. Well lo and behold...
Replies: 14
Views: 1,518
Posted By tea3803

Make sure all your tensioning pulleys and idler...

Make sure all your tensioning pulleys and idler pulleys are free wheeling. I had an idler bearing go out on my Ariens and it ate belts ... also caused stalling every now and then.
Replies: 7
Views: 957
Posted By tea3803

My knowledge won't let me work the inside of an...

My knowledge won't let me work the inside of an engine but I had a 30+ year old Kohler 10HP rebuilt last year. It purrs now ... the price was less than $350.
Replies: 11
Views: 998
Posted By tea3803

Packer

http://forum.doityourself.com/showthread.php?t=171455

Click the link above it will take you there.
Replies: 9
Views: 918
Posted By tea3803

Only problem

Unless they have patched it, the only problem I find with Firefox is that it doesn't support Flash video. I am running version 0.8.
Replies: 11
Views: 998
Posted By tea3803

Packer fan See my post on the Kohler K-241...

Packer fan

See my post on the Kohler K-241 subject line. You may have similar problems.
Replies: 11
Views: 2,393
Posted By tea3803

Thumbs up Fixed

Well not as easily as the title says. I ended up getting a new rectifier regulator ... I could find no other reason for the not charging problem ... installed same and jump started the tractor. It...
Showing results 1 to 25 of 129
 


 
Forum Jump