Search: Posts Made By: DaKine73
Showing results 1 to 18 of 18
Search took 0.01 seconds.
Replies: 20
Views: 2,270
Posted By DaKine73

Once again, sorry for the late postings. So...

Once again, sorry for the late postings.

So I replaced the timing belt. Did all the steps to tdc and belt adjustments. No dice, timing on idle is about -5 degrees past zero. Poor acceleration...
Replies: 20
Views: 2,270
Posted By DaKine73

I did replace the crank positioning sensor, as...

I did replace the crank positioning sensor, as per the Haynes manual code 12 is crack positioning sensor, distributor or ecm failure. The code 12 is still there after replacing the crank sensor.
Replies: 20
Views: 2,270
Posted By DaKine73

So i have not replaced the MAF sensor yet. ...

So i have not replaced the MAF sensor yet.

Today I had a mechanic take a look at the car. I explained to him all i have told you on these posts. He told me 3 possible things. 1 timing 2...
Replies: 20
Views: 2,270
Posted By DaKine73

compression testing

Hello DYI comrades,

Finally purchased the compression test kit. I performed the test on all 4 cylinders, the good news is that they are all within specs, out of 191psi max 142psi min, all of the...
Replies: 20
Views: 2,270
Posted By DaKine73

I checked the MAF sensor. It may be failing but...

I checked the MAF sensor. It may be failing but inconclusive results. That is my next step, to replace it.

i thought of the head gasket, i don't worry about price, i can do the job myself. I just...
Replies: 20
Views: 2,270
Posted By DaKine73

For those inquisitive minds, the timing belt was...

For those inquisitive minds, the timing belt was replaced about a year ago, same with the fuel pump.

i can hear a minor fluctuation of rpms while on idle, the car doesn't have a tach meter so i...
Replies: 20
Views: 2,270
Posted By DaKine73

Thank for the reply, i removed the o2 sensor to...

Thank for the reply,
i removed the o2 sensor to add additional exhaust to escape to test the cat theory. No change there. Still low acceleration.

that crank shaft reluctor idea sounds good as...
Replies: 20
Views: 2,270
Posted By DaKine73

Yes i have, code 12. Obd1. Jumped the terminals....

Yes i have, code 12. Obd1. Jumped the terminals. This code I had for a couple of years without issues. I've just decided to address it (see below threads) still no change.
Replies: 20
Views: 2,270
Posted By DaKine73

Thank you all for the replies, sorry it took so...

Thank you all for the replies, sorry it took so long for me to get back to you.

Here is what I've done so far related to this issue.
Replaced:
alternator (better, stable voltage)
crank...
Replies: 20
Views: 2,270
Posted By DaKine73

1995 Toyota Corolla DX 1.8 4AFE Poor Acceleration

Hello there,

I have a 1995 Toyota Corolla DX 1.8 4AFE engine, automatic transmission, 220000 miles on the odometer. This car has been running fine until a couple of weeks ago. I was stopped on...
01-08-14, 11:51 AM
Replies: 2
Views: 1,115
Posted By DaKine73

Replacing an old coil

Hello to all!

In the past couple of days I noticed that I was not getting any heat from my air handler (it is a Carrier unit with Payne parts). I opened the fan/coil area and noticed that one of...
Replies: 12
Views: 6,087
Posted By DaKine73

Joecaption1 The pressure tank is @ 36psi 2 psi...

Joecaption1
The pressure tank is @ 36psi 2 psi below cut off, how it should be. No problems there. I tested the tank and it holds its pressure fine, no punctured bladder no leaks.
So if you suspect...
Replies: 12
Views: 6,087
Posted By DaKine73

PJmax I don't see anything like that on the...

PJmax
I don't see anything like that on the suction line of the pump. Just rusty old pipes.
Replies: 12
Views: 6,087
Posted By DaKine73

PJmax I did read from Inspectapedia its a cool...

PJmax
I did read from Inspectapedia its a cool place to get info.
I have no water pressure loss, just that hard knock at cut out.
I heard of the foot valve could be slamming shut hard and this...
Replies: 12
Views: 6,087
Posted By DaKine73

Vey Now that you exposed that way, it makes...

Vey
Now that you exposed that way, it makes sense to me now.
But will it still chatter at cut out?
Replies: 12
Views: 6,087
Posted By DaKine73

Vey I must definitely say that's not it... I...

Vey
I must definitely say that's not it... I don't think the switch will be able to shake the pipes.
pjmax... Can you enlighten me a bit more about the check valve theory?
Replies: 12
Views: 6,087
Posted By DaKine73

I'm guessing that would be the case as all I see...

I'm guessing that would be the case as all I see is a pipe leaving the pump thru the wall and then outside in to the ground. But a curios thing is that I was testing the system a little while ago and...
Replies: 12
Views: 6,087
Posted By DaKine73

Lightbulb Well Jet pump knocking sound at cut-out

Hello to all!
I'm new at this forum, I recently purchased my 1st home. This is a 1978 home and the water supply is from a well.
Here is the thing (I've been reading all over the net for this issue...
Showing results 1 to 18 of 18


 
Forum Jump