Search: Posts Made By: AllTrack
Showing results 1 to 25 of 75
Search took 0.01 seconds.
Replies: 1
Views: 1,066
Posted By AllTrack

Does the rep know you have 12' ceilings? I would...

Does the rep know you have 12' ceilings? I would stick to the manufacturer's specs. They are designed to be mounted at a certain height.
Replies: 16
Views: 4,368
Posted By AllTrack

Sorry

I'm looking at page 66.

http://www.avss.net/PDF%20Files/CADDX%20NX8E%20install.pdf

If you're getting a tamper trouble, it's not wired right.

Maybe this is not the right manual.
Replies: 16
Views: 4,368
Posted By AllTrack

Questions

Per your diagram, Zone 6 and Zone 14. Are these two different motion detectors, or one motion where you're using zone 14 as the tamper?

If they are two motions, don't use the tamper terminals on...
Replies: 3
Views: 1,361
Posted By AllTrack

Yes, you can. I use them all the time. As long as...

Yes, you can. I use them all the time. As long as each keypad has a unique address.
You can also set them up as PGM outputs.
Replies: 14
Views: 1,958
Posted By AllTrack

Location 020 is only used if you are using the...

Location 020 is only used if you are using the zones on the keypads. If this is the case there are several items that need to be checked.
Each keypad on the system should be addressed uniquely....
Replies: 4
Views: 3,716
Posted By AllTrack

Then your code is not the master. It is a user...

Then your code is not the master. It is a user code. You do not have to be monitored to change your code.
Try powering down (Transformer and Battery). Connect the battery then transformer. Quickly...
Replies: 4
Views: 3,716
Posted By AllTrack

Press current 4 digit master code then 8 then 1 ...

Press current 4 digit master code then 8 then 1 then new 4 digit code twice. Keypad should beep once if successful.

You cannot hestitate when doing this. There is a very short time limit between...
Replies: 3
Views: 1,184
Posted By AllTrack

Cell Phone is not a Pager.

It's probably not calling your cell cause you don't have an account number programmed or reporting codes.

You might be able to get it to work, if after programming your cell phone number you...
Replies: 20
Views: 43,577
Posted By AllTrack

Press your 4 digit code then 5. The siren will...

Press your 4 digit code then 5. The siren will ring for 2 seconds Wait about 5 more seconds and the BAT indicator should go off. Then press your code and off.
Replies: 27
Views: 43,105
Posted By AllTrack

I'm guessing you followed Ron's instructions to...

I'm guessing you followed Ron's instructions to disable the Telco monitor and communicator.

Turn the alarm on, wait for the exit delay to expire and walk in front of the motions. They should all...
Replies: 20
Views: 43,577
Posted By AllTrack

What does the keypad say?

Does the keypad indicate BAT on it? Is so, does a number come up with it? If it doesn't indicate a zone number, it's the big battery you indicated.
Replies: 9
Views: 18,067
Posted By AllTrack

10 Clicks

If you heard the 10 clicks the installer lockout feature is enabled. Defaulting the panel will default everything "EXCEPT" the installer code so just use it as is.
Replies: 18
Views: 48,986
Posted By AllTrack

Load test battery

Simply metering your battery doesn't always tell you if it's good. With the system powered up (both AC and batt), diconnect the Transformer, then meter the battery while it's still connected to the...
Replies: 9
Views: 18,067
Posted By AllTrack

Caution

Before defaulting the panel. Power down (AC and Battery). Connect Battery then AC. IF you hear 10 quick clicks from the relay, Defaulting the panel WILL NOT default the installer code. So you will...
Replies: 9
Views: 18,067
Posted By AllTrack

Model Number - Find and open the main alarm box....

Model Number - Find and open the main alarm box. Tan metal cabinet somewhere in your house (closet, basement..). Check diagram on inside door cover.

Default master is 1234. Can be 4 or 6 digits...
Replies: 27
Views: 43,105
Posted By AllTrack

* 8 Installer code (6 digits for now). Press 701...

* 8 Installer code (6 digits for now). Press 701 and press 5. Press ## to exit.
Replies: 20
Views: 43,577
Posted By AllTrack

Main Control Battery

That battery is 12 volts; either 4amps or 7. 7 amps is better of course...the system will last longer in the event of a power outage. You can pick one up at Radio Shack or some electrical supply...
Replies: 4
Views: 1,410
Posted By AllTrack

If you have a user code to arm/disarm system,...

If you have a user code to arm/disarm system, simply arm it then disarm. This will clear all bypassed zones.
Replies: 27
Views: 43,105
Posted By AllTrack

Try using 2 zeros at the beginning or at the end...

Try using 2 zeros at the beginning or at the end of the installer code. Forgot which side. You must have changed location 701.
Replies: 7
Views: 2,001
Posted By AllTrack

Transformer Wires

tThe first two terminals on left are your transfomer wires. Disconnect one and the battery. then put the battery on then the wire. You'll have to reset the clock after that.
Replies: 10
Views: 1,693
Posted By AllTrack

What zones are you planning to use the motion and...

What zones are you planning to use the motion and door sensors on, and what are your current zones now? Then we can give you step by step instructions.
Replies: 5
Views: 40,889
Posted By AllTrack

No battery for chime

If BAT is displayed without a number, then it is the battery in the main box. If it shows a zone number, then it's a wireless transmitter battery.
If you replace the panel battery, wait 24 hours...
Replies: 6
Views: 1,871
Posted By AllTrack

Are you certain that the beeping is coming from...

Are you certain that the beeping is coming from the keypad or your electric smoke detectors? Often times it's difficult to pinpoint where the beeping is coming from. Is there a smoke detector near...
Replies: 11
Views: 6,197
Posted By AllTrack

On the original transmitters, did they wire...

On the original transmitters, did they wire external contacts, or are they using the magnet right next to the transmitter?


I'm sorry, typed numbers wrong. 4549 instead of 4945.

Maybe Ron is...
Replies: 6
Views: 1,871
Posted By AllTrack

I would look for loose screw terminals or wires...

I would look for loose screw terminals or wires at the AUX POWER (4 & 5) terminals in the main control. If your keypads are not indicating any troubles, they may be just losing power, perhaps when...
Showing results 1 to 25 of 75
 


 
Forum Jump