Search: Posts Made By: brownbagg
Showing results 1 to 25 of 194
Search took 0.13 seconds.
Replies: 4
Views: 7,046
Posted By brownbagg

if they are in a cup dimple in the slab, just mix...

if they are in a cup dimple in the slab, just mix of some cement and sand and slap on it.
Replies: 6
Views: 2,313
Posted By brownbagg

yes, it will be dark when applied and it will...

yes, it will be dark when applied and it will turn lighter over time. It not just this product but all sealer will do this.
08-03-05, 08:18 PM
Replies: 1
Views: 935
Posted By brownbagg

air compressor wiring

I have aquire an shop AC that can run off 110 or 220. I plan on wiring to 220 but want to make sure one question first. The wiring diagram has line 1, line 2 and ground. Its only 15 amps at 220. my...
07-15-05, 10:14 PM
Replies: 2
Views: 1,239
Posted By brownbagg

what I meant was, cut a small section of wire,...

what I meant was, cut a small section of wire, about three inches long and wire nut it with incoming wire and the outgoing to next receptacle. so it would be 3 #6 under one wirenut. Is this correct.
07-15-05, 07:31 PM
Replies: 2
Views: 1,239
Posted By brownbagg

50 amp, pigtail

when I wired my house, I pigtailed all the receptacle in that circuit. Now I want to add a welding machine circuit in the shop. I want an recetacle at each end of the bldg so I can move the machine...
07-06-05, 09:12 PM
Replies: 1
Views: 968
Posted By brownbagg

welding machine.

I need to wire an outlet for my welding machine. a typical lincoln cracker box. I have been running off the dryer outlet but I need one in the shop now. I think its a 30 amp outlet. I want to run it...
07-03-05, 02:12 PM
Replies: 2
Views: 904
Posted By brownbagg

subpanel, unattach garage.

I been following another threads and just want to clear up a point. unattach garage, no phone lines. 4 wires back to main in conduit, seperate neutral and ground. what about ground rod at garage,...
Replies: 6
Views: 1,102
Posted By brownbagg

welding lense

what is a good darknest for lenses. the one I got is way to dark. what do yall use.
Replies: 6
Views: 1,680
Posted By brownbagg

there a good one of Ebay about Arc welding. I...

there a good one of Ebay about Arc welding. I bought a copy last week for $20
10-19-04, 09:43 AM
Replies: 1
Views: 697
Posted By brownbagg

B&D book

last year, well couple years ago when I was wiring my house, it was mention here that the B&D book had a couple mistakes in it. I cannot return to those messages. anybody remember what those mistakes...
04-03-04, 05:09 PM
Replies: 13
Views: 1,566
Posted By brownbagg

Ok back to the orignal question.... What type...

Ok back to the orignal question.... What type hookup do I need?
03-30-04, 10:38 AM
Replies: 13
Views: 1,566
Posted By brownbagg

pipe cannot be section because its four feet...

pipe cannot be section because its four feet below dirt.
03-29-04, 07:05 PM
Replies: 13
Views: 1,566
Posted By brownbagg

pulling wire

couple weeks I need to pull (3) # 2 and (1)# 8 through 150 feet of 2 inch pvc conduit. (2) 90 and (2)45 I,m assume I can pull all 4 wire at once. what type hookup do I need.
03-24-04, 06:55 PM
Replies: 1
Views: 726
Posted By brownbagg

prices

need to make a budget, where can I find price on #2 copper, thwn
Replies: 3
Views: 1,237
Posted By brownbagg

commerical roll up doors

anybody know where I can buy the chain fall type outfit for a commerical roll up door?
Replies: 1
Views: 868
Posted By brownbagg

small satellite

can you paint one of those small satellite dish, or will it mess up the signal
Replies: 2
Views: 1,810
Posted By brownbagg

rca projection.

i was given an rca p46770ck projection Tv. It does not turn on, I know nothing about this set. Any ideas, reset button? Just looking before I haul it to the shop.
01-01-04, 08:04 AM
Replies: 3
Views: 933
Posted By brownbagg

has mention earlier, voltage drop is not a...

has mention earlier, voltage drop is not a problem, Yes I have a cracker box welder but it only required a 50 amp breaker, I am in the deep south so no heating and cooling. The 100 amp service is way...
12-31-03, 08:03 PM
Replies: 3
Views: 933
Posted By brownbagg

Nelson- quick question- grounding

I ordered my shop last weel. its going to be an all metal commerical bldg on slab. Not connected to the house. I have plan on running a 100 amp sub panel from the house using 4 condactor in 2 inch...
12-31-03, 07:57 PM
Replies: 3
Views: 828
Posted By brownbagg

I got a GE dryer too, my model number was inside...

I got a GE dryer too, my model number was inside the door and on the back. My model number is DSXR453VOWW. It seems to be the same.

But go to www.sears.com you can order any part for any make of...
12-31-03, 07:49 PM
Replies: 17
Views: 2,465
Posted By brownbagg

It will not be that bad, I got a copy of the new...

It will not be that bad, I got a copy of the new NEC at the library and just followed it. Once you familiar with the codes its pretty simple. Only thing he busted me on was the green wire nuts.
Replies: 25
Views: 5,907
Posted By brownbagg

I have the sherwin william epoxy on my concrete...

I have the sherwin william epoxy on my concrete floor. It was $70 a gallon. Hard as nails. But if it get wet, slippery as ball bearing. I would do it again in a heartbeat. Very happy.
11-30-03, 08:18 PM
Replies: 4
Views: 1,174
Posted By brownbagg

I did my walls myself it really simple, for the...

I did my walls myself it really simple, for the attic I had cellious blow in by a contractor, worth every penny. The money you save on the walls you can add for extra insulation in the attic
Replies: 3
Views: 1,757
Posted By brownbagg

it will be cheaper just to call a concrete truck...

it will be cheaper just to call a concrete truck to deliever, Trust me do the math.
Replies: 7
Views: 3,423
Posted By brownbagg

40 and falling, no go 32 and rising , OK.

40 and falling, no go
32 and rising , OK.
Showing results 1 to 25 of 194
 


 
Forum Jump