Search: Posts Made By: Tool Nut
Showing results 1 to 14 of 14
Search took 0.02 seconds.
Replies: 2
Views: 1,418
Posted By Tool Nut

Briggs carb problem

Hello all, My grandfather has a gas edger with a briggs model 80202-2221-01 on it. It was given to him. It wont start. I can get it to run on carb cleaner so I'm going to rebuild the carb. Thats not...
Replies: 1
Views: 1,092
Posted By Tool Nut

Briggs 28n707 head removal

I'm looking to remove the head on a 28n707 but have never removed one on an overhead valve motor. I would imagine that it just unbolts and the only loose parts are the pushrods from the cam. I want...
Replies: 3
Views: 1,075
Posted By Tool Nut

If you have enough room in the floor framing for...

If you have enough room in the floor framing for the drain line then it should be ok. DO NOT cut any floor framing to install any pipes. Don't forget the trap under the floor. In my trailer the...
Replies: 5
Views: 2,294
Posted By Tool Nut

I know that Ideal use Black for Quad and Blue for...

I know that Ideal use Black for Quad and Blue for RG6.

Jeremy
Replies: 5
Views: 950
Posted By Tool Nut

I think he means the white Home Depot wire you...

I think he means the white Home Depot wire you can buy with the ends already attached.

Is there an open basement in there I would rather drop the wire into the basement and pull it up into the...
Replies: 4
Views: 14,673
Posted By Tool Nut

If you clamp a a piece of 1x4 to the plywood it...

If you clamp a a piece of 1x4 to the plywood it is easier to make a nice straight cut. Just remember to offset it by the amount that the blade offset from the edge of the shoe.

Jeremy
06-25-08, 08:05 PM
Replies: 11
Views: 10,651
Posted By Tool Nut

This is not always true. I never use mesh tape on...

This is not always true. I never use mesh tape on regular drywall but I will when I repair plaster. If you v out a crack in a plaster wall and wet it, then put a layer of mesh tape on it and go over...
06-25-08, 07:51 PM
Replies: 2
Views: 2,506
Posted By Tool Nut

First of all are you sure it's paint and not...

First of all are you sure it's paint and not glue? I just did a kitchen in my mother in laws house with 3 layers of paper and some hard glue. Get a bottle of DIF fast acting and spray it down good...
06-22-08, 06:43 AM
Replies: 20
Views: 1,668
Posted By Tool Nut

I was just looking @ the code and can't find...

I was just looking @ the code and can't find where it says that the microwave needs to be separate? Does anybody have the article#?

The only thing I found was in article 220.55 it says that if a...
06-22-08, 06:20 AM
Replies: 20
Views: 1,668
Posted By Tool Nut

I wonder why you can't tie in a Stove and a...

I wonder why you can't tie in a Stove and a microwave? A gas stove only uses electric for the piezo ignition and for the clock.

Jeremy
Replies: 3
Views: 965
Posted By Tool Nut

Metabo is probably the best grinder on the...

Metabo is probably the best grinder on the market. I have Makita, DW, Milwaukee and a few others and still love the Metabo. It has a toolless blade nut which beats loosing the spanner wrenches like I...
06-21-08, 07:47 PM
Replies: 18
Views: 47,504
Posted By Tool Nut

As Mark said use a 3/4" drill and then put a...

As Mark said use a 3/4" drill and then put a washer on the stud.

Jeremy
06-21-08, 07:35 PM
Replies: 10
Views: 33,315
Posted By Tool Nut

Sounds Like open neutral. Check the GFI load side...

Sounds Like open neutral. Check the GFI load side for neutral.

Jeremy
06-21-08, 07:18 PM
Replies: 20
Views: 1,668
Posted By Tool Nut

Is it OK to put a dishwasher and a under cabinet...

Is it OK to put a dishwasher and a under cabinet Microwave on the same circuit? I figure normally you would run a dishwasher after dinner so the micro would be off anyway.

Jeremy
Showing results 1 to 14 of 14


 
Forum Jump