Search: Posts Made By: oopsy59
Showing results 1 to 13 of 13
Search took 0.02 seconds.
Replies: 7
Views: 1,358
Posted By oopsy59

You said that the fuel filter was changed prior...

You said that the fuel filter was changed prior to this problem starting. I believe I would replace the fuel filter again . Could have gotten a bad filter or a piece of trash. That would be the...
Replies: 3
Views: 887
Posted By oopsy59

will try easiest and cheapest route first. The...

will try easiest and cheapest route first. The negative wire would be the easiest over getting into the circuit board.Thanks OOPSY 59
Replies: 3
Views: 887
Posted By oopsy59

oopsy59

:confused: 2000 Chevy Blazer with 6 cylinder full power. Problem with fuel gauge swinging from full to empty. In the past I had another older model pickup 1986 that had the same problem It was the...
Replies: 17
Views: 11,924
Posted By oopsy59

The trans fluid does not reach the lifters. The...

The trans fluid does not reach the lifters. The theory behind all that was to loosen the valves. That is why I do not recommend. It seems rather ironic that putting trans fluid on your hogs will...
Replies: 10
Views: 1,743
Posted By oopsy59

There is an adjustment that is recommended by...

There is an adjustment that is recommended by Dodge when you have the trans pan pulled off and changing oil. I have a 2000 Dodge and it does the same thing. Worse in cold weather. If you will get a...
Replies: 7
Views: 1,417
Posted By oopsy59

No luck with the head removal check air breather...

No luck with the head removal check air breather housing usually located under intake. If oil was leaking into the area of the head you would most likely be smoking terribly bad. If not pulsating...
Replies: 4
Views: 2,608
Posted By oopsy59

It sounds like an air leak. Have had this...

It sounds like an air leak. Have had this problem in the past. Check gas lines. There might a pin hole and not visible to the naked eye. Also experienced this problem. The high rev is air...
Replies: 4
Views: 2,414
Posted By oopsy59

After you removed and cleaned carb did you...

After you removed and cleaned carb did you readust your hi and lo needles. How about before you took the carb apart? If not try seating both needles then back out about one turn. Then work from...
Replies: 17
Views: 11,924
Posted By oopsy59

If your vehicle has hydraulic lifters then after...

If your vehicle has hydraulic lifters then after sitting for several days older vehicles will have a tendency to bleed down on the lifters. Oil additives might clean away more than you want . A...
05-21-08, 06:12 AM
Replies: 3
Views: 2,529
Posted By oopsy59

If it is a spin cast there is a spring where the...

If it is a spin cast there is a spring where the bail pivots on one end. The tips of these springs will break whereas all tension on the bail is lost so bail will not close when handle is turned. If...
Replies: 3
Views: 4,716
Posted By oopsy59

First question why do you want to replace the...

First question why do you want to replace the head? OOPSY 59 Pul off the plastic covers the look where the spark plug was inserted and there lies your head. Simply unscrew the bolts and pull the...
Replies: 11
Views: 10,607
Posted By oopsy59

You are sucking air into the engine. By the...

You are sucking air into the engine. By the choke being closed it reduces air flow and then after it warms awhile that is causing your other problems the popping is too much gas in the cylinder and...
Replies: 4
Views: 1,342
Posted By oopsy59

After driving commerically for 30 years one...

After driving commerically for 30 years one concern was lug nuts. Safety inspection aside it is there for reason. They are not hard to replace and will eliminate a concern.
Showing results 1 to 13 of 13


 
Forum Jump