Search: Posts Made By: Gotrek
Showing results 1 to 25 of 64
Search took 0.03 seconds.
02-21-07, 05:38 PM
Replies: 17
Views: 51,541
Posted By Gotrek

You're not french speaking are you :) Sorry the...

You're not french speaking are you :) Sorry the name was misleading.

The compressor pump is a splash oiled piston type with new oil. The pump itself is almost new.

I did a quick test and let...
02-21-07, 04:22 PM
Replies: 17
Views: 51,541
Posted By Gotrek

Merci Marc, ta raison le moteur devient chaud...

Merci Marc, ta raison le moteur devient chaud seulement apres avoir rejoin 80 livres de pression quand il doit force un peu. Ca doit etre ca car il deviens plus chaud vers l'arriere que l'avant...
02-21-07, 12:17 PM
Replies: 17
Views: 51,541
Posted By Gotrek

You're probably right. I was also thinking of...

You're probably right. I was also thinking of the possibility that the start circuit is not disengaging as it should. this would lead to overheating would it not?
02-20-07, 09:24 PM
Replies: 17
Views: 51,541
Posted By Gotrek

Ok I must of goofed somewhere sorry to bump this...

Ok I must of goofed somewhere sorry to bump this up again. new question same motor.

I was refinishing the compressor tank (paint job) and took the compressor apart.

I decided to replace the...
02-09-07, 06:24 PM
Replies: 17
Views: 51,541
Posted By Gotrek

There is no play in this motor at all (non...

There is no play in this motor at all (non detectable by me) I'ts operating well so far.
02-07-07, 10:19 AM
Replies: 17
Views: 51,541
Posted By Gotrek

The motor is up and running thank you for your...

The motor is up and running thank you for your assitance. It's not lubricated yet though. I was going to use a dielectric grease? Is that ok? Which parts should be lubricated and which should not?
02-06-07, 02:18 PM
Replies: 17
Views: 51,541
Posted By Gotrek

I've given it a thorough cleaning will update...

I've given it a thorough cleaning will update tomorrow with the results.
02-02-07, 07:56 PM
Replies: 17
Views: 51,541
Posted By Gotrek

Capacitor start electric motor failure

I realize this may be the wrong section please advise if it is.

I'm about to crack open and old compressor motor to clean it in hopes to fix a problem. I'd like to offer symptoms of what's...
12-05-05, 07:11 AM
Replies: 14
Views: 2,153
Posted By Gotrek

I agree with you mudslinger only the tape has...

I agree with you mudslinger only the tape has been applied at this poitnand I'm already very satisfied with myself :)
12-02-05, 09:53 AM
Replies: 14
Views: 2,153
Posted By Gotrek

I've got paper tape and I'll let each coat dry ...

I've got paper tape and I'll let each coat dry I've read all the onlinetapping corners how too's so I'm ready to attempt it.

But first I still need to remove the old tap that's on the wall...
12-02-05, 08:36 AM
Replies: 14
Views: 2,153
Posted By Gotrek

Wow I'm done and it was not bad and looks ok... ...

Wow I'm done and it was not bad and looks ok... I took pictures for your entertainment and will upload them later.

I mean I did a crappy job compared to a pro but it turned out as good as I...
12-01-05, 10:01 AM
Replies: 14
Views: 2,153
Posted By Gotrek

If anyone is still reading this a bit more...

If anyone is still reading this a bit more advice.

I've got my 5/8" sheetrock. 4 sheets one extra in case screw up.


I've ripped out the entire ceiling last night. Not bad job, pretty happy...
11-30-05, 08:47 AM
Replies: 14
Views: 2,153
Posted By Gotrek

No go on the pushing back up. I tried and tried...

No go on the pushing back up. I tried and tried tightening it by screwing screws every 3" no go it's finished. So I started moving the cellulose and wood chips out of the valleys between the studs....
11-29-05, 12:15 PM
Replies: 14
Views: 2,153
Posted By Gotrek

Thanks guys. I'll try to push it back up first...

Thanks guys. I'll try to push it back up first but a goo 12" squard section needs to be replaced for sure so with that siad if I do repair instead of change the hole thing I have to stiuck with 3/8"...
11-29-05, 11:13 AM
Replies: 14
Views: 2,153
Posted By Gotrek

I agree I've kind of resolved myself that this is...

I agree I've kind of resolved myself that this is what I'll do since it's such a small ceiling.

I've done walls before (mounting the drywall boards) and patches but never ceilings and never taped...
11-29-05, 07:48 AM
Replies: 14
Views: 2,153
Posted By Gotrek

I wanted to clarify only the area around the fan...

I wanted to clarify only the area around the fan seems to be sagging however I did not clear the cellulose elsewhere tto check.

I'm going to clear it away tonight and find where the sheet of...
11-29-05, 07:13 AM
Replies: 14
Views: 2,153
Posted By Gotrek

Sagging Drywall hole in the ceiling.

The Previous owner installed a ceiling fan in my bathroom at some point which is good. The drywall around the fan is sagging and cracked and he forgot to insulate the ducting which is bad. I Went in...
11-09-05, 10:17 AM
Replies: 6
Views: 1,104
Posted By Gotrek

yep it's on a gfci and it's seperated from the...

yep it's on a gfci and it's seperated from the water by glass sheets. It's not sitting over water.

Thank you.
11-09-05, 09:42 AM
Replies: 6
Views: 1,104
Posted By Gotrek

I'm sorry my fault those aren't the actual...

I'm sorry my fault those aren't the actual sockets I just used those to help me draw the circuit. I coulnd't find any like mine in google so I used my paint skills again.

Basiclly they are...
11-09-05, 09:20 AM
Replies: 6
Views: 1,104
Posted By Gotrek

Mmm there isn't room or appropriate mounting...

Mmm there isn't room or appropriate mounting area. I looked for an inline switch but couldn't find any at the store. I guess I can find an old lamp with one somewwere in the scrap. There is a...
11-09-05, 08:55 AM
Replies: 6
Views: 1,104
Posted By Gotrek

Connecting three light sockets to one powersoure/switch

I have three light sockets that I want to hook together to run from one Power cord (Standard 110 outlet) They will be fitted with 13W compact fluorescent bulbs.

Each socket has a turn switch to...
Replies: 4
Views: 3,368
Posted By Gotrek

Auto and ys it seems to be bad, truck would not...

Auto and ys it seems to be bad, truck would not start so I jumped the connector on that blue relay beside the battery and it fired right up, I've got a new relay on order.
Replies: 4
Views: 3,368
Posted By Gotrek

Sorry forgot to post, the battery terminals are...

Sorry forgot to post, the battery terminals are the stock ones which I've cleaned and lubed with dielectric grease and I've tested all the ground points to the cassie and starter. I'm starting to...
Replies: 4
Views: 3,368
Posted By Gotrek

Starting woes on a 1992 Nissan Pathfinder

1992 Pathfinder with 3.0 V6 Automatic 4x4.

Symptoms in January - Would not start, would tick(fuse or relay popping tick sound) dahs lights would dim and nothing. Slam the hood and it would fire...
Replies: 2
Views: 827
Posted By Gotrek

Cutlass Supreme S questions.

The car

1992 Cutlass Supreme S, 3.1 Liter, automatic, 140 000kms, I don't know too much about the car yet i haven't looked at it much. I'm used to working on older pre-computer cars.

The car...
Showing results 1 to 25 of 64
 


 
Forum Jump