Search: Posts Made By: Mister Ed
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Replies: 26
Views: 6,286
Posted By Mister Ed

Found the problem!!! Just like Troop predicted......

Found the problem!!! Just like Troop predicted...
http://img704.imageshack.us/img704/1149/img0016cd.jpg
a bad solder joint. Looks like they were pretty stingy with the solder all around.
...
Replies: 26
Views: 6,286
Posted By Mister Ed

No matter where the LO setting is, the circulator...

No matter where the LO setting is, the circulator pump will stop when the temp reaches the low setpoint -10 in order to give priority to domestic hot water. My HI setpoint is not working so I had to...
Replies: 26
Views: 6,286
Posted By Mister Ed

Thanks, I read that yesterday. It's what prompted...

Thanks, I read that yesterday. It's what prompted me to look more closely at how my heating system operates.
Replies: 26
Views: 6,286
Posted By Mister Ed

Thanks for the tips :thumbup:. I'm so...

Thanks for the tips :thumbup:. I'm so disorganized... right now I have to find my soldering iron, lol! I'm gonna wait 'til tomorrow to do this. If something goes awry (and it usually does,) at least...
Replies: 9
Views: 27,654
Posted By Mister Ed

I hate when they do stuff like this :wall:, why...

I hate when they do stuff like this :wall:, why can't they just be fair about it? They'll probably make more money in the long run from good word of mouth/reputation, repeat customers, etc.
Replies: 9
Views: 27,654
Posted By Mister Ed

Here are some of the details of the TSB: ...

Here are some of the details of the TSB:

ENGINE
EG024-04
REVISED

Title:
M.I.L. "ON" DTC P0420

Models:
Replies: 26
Views: 6,286
Posted By Mister Ed

I downloaded the schematic as well. I guess I...

I downloaded the schematic as well. I guess I shoulda done this in the first place, duh! With 1K energized, I should have voltage at ZR, which I don't. I believe this is the problem since that powers...
Replies: 26
Views: 6,286
Posted By Mister Ed

Yes, there is a mixing valve to lower the temp of...

Yes, there is a mixing valve to lower the temp of the domestic hot water. I have recently bumped up the temps a little, but I think the system has been operating this way for a long time. I only just...
Replies: 26
Views: 6,286
Posted By Mister Ed

HI set to 200 LO set to 170 DIFF set to 15

HI set to 200
LO set to 170
DIFF set to 15
Replies: 26
Views: 6,286
Posted By Mister Ed

Honeywell R8182D not reaching HI limit

I have a Burnham furnace with a Beckett burner, 3 heating zones and a tankless coil. According to the Honeywell manual, when a thermostat calls for heat, both the circulator relay and burner relay...
Replies: 17
Views: 1,301
Posted By Mister Ed

Most, if not all modern cars have a blocker in...

Most, if not all modern cars have a blocker in the fuel filler tube to prevent a hose being inserted. Try to put a hose in the fuel filler and see how far it goes in. I'll bet not much. Locking gas...
Replies: 3
Views: 8,128
Posted By Mister Ed

1. Turn the ignition switch to the ON (II)...

1. Turn the ignition switch to the ON (II) position
2. Press the select/reset knob repeatedly until the engine oil life is displayed.
3. Press and hold the select/reset knob for about 10 seconds....
Showing results 1 to 12 of 12


 
Forum Jump