Search: Posts Made By: bdubrow
Showing results 1 to 12 of 12
Search took 0.01 seconds.
07-24-10, 07:01 PM
Replies: 3
Views: 3,466
Posted By bdubrow

Sundance Optima 880 Control Panel Malfunction

Whenever I press either the Light, Blower, Jet1 or Jet2 button they all come on. They do not seem to work independently as they should. I tried turning the power off to the Spa to reset but that...
02-13-09, 06:20 AM
Replies: 2
Views: 2,099
Posted By bdubrow

Thanks for the info about the Hardiebacker, the...

Thanks for the info about the Hardiebacker, the 24OC studs were what was there. I did go to the website and sure enough they recommend maximum 16OC studs. I guess I have some extra work this...
02-12-09, 09:39 AM
Replies: 2
Views: 2,099
Posted By bdubrow

Concerned about weight of wall tile

I am tiling around a bathtub and the shipping weight for the tile was about 300 lbs. should I be concerned? I have 2x10 16 OC joist and the studs are 2x4 24 OC covered with Hardiebacker. The...
Replies: 7
Views: 3,324
Posted By bdubrow

Thanks for your input, I did manage to get...

Thanks for your input, I did manage to get everything working again. The manual information and directions worked exactly as described. It had a learning feature where all I had to do was "trip"...
12-25-08, 07:22 AM
Replies: 5
Views: 1,272
Posted By bdubrow

Are you saying I should lay the new plywood...

Are you saying I should lay the new plywood perpendicular to the way the old plywood is laid or do you mean just to stagger the joints?
12-25-08, 06:27 AM
Replies: 5
Views: 1,272
Posted By bdubrow

Adding underlayment for ceramic tile install

I currently have a subfloor of 19/32 on 16 inch OC 2x10 joists. I want to install a tile floor and need to increase the hight of the floor a little. I was thinking of adding another 19/32 and a 1/4...
Replies: 2
Views: 1,880
Posted By bdubrow

Question Toilet flange too high after removing dry mortar bed

I plan on retiling a bathroom floor, after removing the old tile and the dry mortar bed I realized the flange might be too high for the new floor. It currently sits 1 3/4 from the subfloor, I figure...
Replies: 27
Views: 11,386
Posted By bdubrow

Tom, I do have the entire installation manual...

Tom,
I do have the entire installation manual for the Rollins System V. It is not the home owners users version but the installtion manual for installers. A few months ago I accidently wiped out...
Replies: 1
Views: 2,037
Posted By bdubrow

Programming ITI SX V House Code

I had to reprogram my ITI SX V and I think I managed to do so using the hardwired touchpad. When I use the touchpad I see all the sensors and their settings. However, I can not seem to trip any of...
Replies: 7
Views: 3,324
Posted By bdubrow

Question I did manage to get the installation manual from...

I did manage to get the installation manual from a GE website (https://portal.gesecurity.com) and it does appear to be an ITI SX V. The r rr status means that the CPU is in a bootup mode. After...
Replies: 7
Views: 3,324
Posted By bdubrow

Any ideas on what might have happend? My old...

Any ideas on what might have happend? My old battery was Portalac PE6V32 3.2AmH and the replacement I was sent was 3.8AmH but did not notice until after I troed to attach it. Could that have caused...
Replies: 7
Views: 3,324
Posted By bdubrow

Rollins System VI battery changing

I went to change the battery on my Rollins System VI and now it is flashing lower case r's. I made sure the wires were connected to the correct terminals before I put in the new battery. Even...
Showing results 1 to 12 of 12


 
Forum Jump