Search: Posts Made By: tovo1234
Showing results 1 to 12 of 12
Search took 0.01 seconds.
07-06-15, 09:12 PM
Replies: 5
Views: 869
Posted By tovo1234

Thank you everyone for your responses. Sorry for...

Thank you everyone for your responses. Sorry for my slow response as I don't normally post a question then not respond although on the 4th of July my next door neighbor have an accident and was...
07-03-15, 09:59 PM
Replies: 5
Views: 869
Posted By tovo1234

Outdoor GFI tripping under load

OK everyone I am stumped with my GFI curcut and need some help which is greatly appreciated.

Background into the circuit

I installed a dedicated outdoor curcut for my outdoor needs. It is 15...
Replies: 12
Views: 2,753
Posted By tovo1234

The whole system shut down worked. Thank you so...

The whole system shut down worked. Thank you so very much for your help Ron.
Replies: 12
Views: 2,753
Posted By tovo1234

Says View Trouble Zone Faults Then I...

Says

View Trouble
Zone Faults

Then I answer with a *

No Zone Faults
Replies: 12
Views: 2,753
Posted By tovo1234

Hi Ron, I got the new heat sensor in. Looking at...

Hi Ron, I got the new heat sensor in. Looking at the keypad the trouble light is on but, in system troubles/zone fault there are no errors. Also in the bypass for all the zones were are not open...
Replies: 12
Views: 2,753
Posted By tovo1234

You are very perceptive Ron. Upon reading your...

You are very perceptive Ron. Upon reading your last message I went to the kitchen and garage and found a heat sensor out in our garage I never remember them installing.

So we have a separate heat...
Replies: 12
Views: 2,753
Posted By tovo1234

Hey Ron, I am sure the previous smoke was a...

Hey Ron,

I am sure the previous smoke was a two wire. The previous smoke model is below.
http://www.alarmhow.net/manuals/DSC/Sensors/Smokes/MN220%202-Wire%20Smoke%20Installation%20Manual.pdf

I...
Replies: 12
Views: 2,753
Posted By tovo1234

Thanks again for your help Ron. I am using...

Thanks again for your help Ron.

I am using the previous resistor which is a 2.2k ohm. Please see attached picture for placement of the resistor in the last zone of the DSC PC5010.

For the...
Replies: 12
Views: 2,753
Posted By tovo1234

DSC PC5010 smoke error code after replacement of smoke detectors

So I have a 10 year old home alarm system DSC PC5010 that is installed in my house. I got a smoke detector error on one of my MN220T 2 wire (only 2 incoming wires) so I decided to replace both of...
Replies: 8
Views: 3,340
Posted By tovo1234

Good morning PJmax, Worked perfectly....

Good morning PJmax,


Worked perfectly. Thank you thank you. Now I have a heat sensor warning. If it's not one thing it's another. It should be much easier to replace. Thanks again.


Cheers...
Replies: 8
Views: 3,340
Posted By tovo1234

Many thanks PJmax. I'll report back tomorrow on...

Many thanks PJmax. I'll report back tomorrow on how it goes.
Replies: 8
Views: 3,340
Posted By tovo1234

Wiring help on replacing 240-COe CO2 with 260-COe

Hello Everyone,

I am hoping someone can help me on a replacement of my 240-COe CO2 sensor with a never model 260-COe CO2 sensor.

For some background. We have had a security system professional...
Showing results 1 to 12 of 12


 
Forum Jump