Search: Posts Made By: ednu99
Showing results 1 to 25 of 142
Search took 0.06 seconds.
Replies: 5
Views: 228
Posted By ednu99

Thank you for the replies, going to look at these...

Thank you for the replies, going to look at these suggestions today.
Replies: 5
Views: 228
Posted By ednu99

It's a KitchenAid model KBFS20EVBL3 I...

It's a KitchenAid model KBFS20EVBL3

I checked the manual and there is no mention of a drain or condensation pan that needs to be emptied. I'm certain there is no "drain" going out anywhere. I...
Replies: 5
Views: 228
Posted By ednu99

KitchenAid bottom freezer dripping water to floor

My KirtchenAid bottom freezer refrigerator has started leaking water onto the floor. If I open the freezer compartment and pull out the sliding drawer there is water frozen on the bottom of the...
Replies: 6
Views: 312
Posted By ednu99

Thanks PJ, I did consider a door bell...

Thanks PJ, I did consider a door bell transformer, it was just that having either a plug-in or external mount transformer outdoors didn't seem like a good solution. Sounds like I need to...
Replies: 6
Views: 312
Posted By ednu99

I understand the low voltage design but why not a...

I understand the low voltage design but why not a solution that incorporates a transformer that could be installed in a junction box. The camera could then be mounted to the JB with no visible...
Replies: 6
Views: 312
Posted By ednu99

POE would work but I was really looking for a...

POE would work but I was really looking for a wireless transmission so no cables would need to be run as cable routing in this case would be extremely difficult.

If I can power the wireless...
Replies: 6
Views: 312
Posted By ednu99

Camera with a hard wired power source

Iím looking for an exterior security camera to monitor a building entrance. There is a 120 Volt AC power source available at the location we wish to mount the camera. The problem is most cameras Iíve...
11-26-18, 10:42 AM
Replies: 3
Views: 886
Posted By ednu99

It does not have a hot water feature and I've not...

It does not have a hot water feature and I've not observed any water leakage into the interior.

Is it possible the start capacitor could be causing the problem, an electrician I know mentioned...
11-26-18, 06:54 AM
Replies: 3
Views: 886
Posted By ednu99

Water fountain tripping GFCI

We have a water fountain that trips the gfci breaker immediately when plugged in. I don't think the breaker is faulty as we have two water fountain coolers and I've switched them around and the one...
06-14-18, 07:18 AM
Replies: 4
Views: 336
Posted By ednu99

We have considered going with led but just don't...

We have considered going with led but just don't have the funds at this moment for a complete upgrade so we were trying to get by for a couple more years with the HID.

I've actually recommend...
06-13-18, 05:18 PM
Replies: 4
Views: 336
Posted By ednu99

Metal Halide - ballast/capacitor question

2 years ago we replaced all 64 of our metal halide bulbs and our reading went from around 35 ft candles to about 65. We then replaced all the capacitors and the readings went to around 100.

Since...
04-29-18, 06:50 AM
Replies: 6
Views: 356
Posted By ednu99

I understand this is a code requirement but I'm...

I understand this is a code requirement but I'm just curious about what the reasoning is for requiring a disconnect switch on the circuit, especially if mounted withing the same box.
04-28-18, 11:57 AM
Replies: 6
Views: 356
Posted By ednu99

Thanks Ray, "You will need a disconnect...

Thanks Ray,

"You will need a disconnect where it enters the shed. A simple light switch will work for that. "

I'm assuming I can mount a 2 gang box on the inside of the shed, with a switch and...
04-28-18, 10:35 AM
Replies: 6
Views: 356
Posted By ednu99

Another outbuilding circuit question

We need a 120V circuit to an outbuilding that sits only about 20 feet from the house. The circuit will only be used for a battery charger so the amperage draw will be very small. From what I've read...
10-17-17, 07:25 AM
Replies: 4
Views: 493
Posted By ednu99

LED lights see voltage

This might be more of an electronics question but I'll start here. I have an LED worklight that glows slightly even when switched off. When unplugged from the receptacle the led's go completely off....
05-14-17, 10:18 AM
Replies: 4
Views: 1,210
Posted By ednu99

Thanks Ray, The reason I used pdf is that the...

Thanks Ray, The reason I used pdf is that the drawing was done in AutoCad Lite. I'm used to sending it to a plot device, a PDF in this case but I'll try exporting to a JPEG file next time. Thanks...
05-14-17, 08:09 AM
Replies: 4
Views: 1,210
Posted By ednu99

Thanks, the UF feeder has a gfci breaker in the...

Thanks, the UF feeder has a gfci breaker in the service panel so I'm guessing the existing GFCI receptacle isn't necessary? These are existing so they come from different directions.
05-14-17, 07:56 AM
Replies: 4
Views: 1,210
Posted By ednu99

Outdoor receptacle and faucet mounting

I'm looking for options to redo a poorly installed outdoor receptacle with a near by water faucet. My thoughts are to sink a 4X4 pole into the ground and have a water faucet attached to one side and...
04-26-17, 02:34 PM
Replies: 6
Views: 610
Posted By ednu99

They're not used, they're brand new, that's why...

They're not used, they're brand new, that's why I'm questioning the supplier who is telling me they are fine and doesn't want to replace them. I'm looking for other opinions before we go to the...
04-26-17, 08:56 AM
Replies: 6
Views: 610
Posted By ednu99

Damaged HID lighting capacitors

We're replacing all the lighting capacitors in our facility. The lights are 1000W Metal Halide fixtures. We purchased 30 capacitors and after inspection I found that 7 are dented, some worse than...
11-02-16, 10:07 AM
Replies: 18
Views: 688
Posted By ednu99

I met with an electrician yesterday and I believe...

I met with an electrician yesterday and I believe we have a workable plan. Each of the 4 courts has its ballasts mounted on a wall mounted board, 16 for each court, one for each light. What we're...
11-01-16, 06:52 AM
Replies: 18
Views: 688
Posted By ednu99

The 3P service is 120/240, not 208. "All switches...

The 3P service is 120/240, not 208. "All switches and/or contactors will be placed after the breakers." I guess I don't see how a single contactor as mentioned could be placed after the breakers. You...
11-01-16, 06:30 AM
Replies: 18
Views: 688
Posted By ednu99

Thank you for the replies. All work will...

Thank you for the replies. All work will certainly be done by licensed electricians. I'm just looking to be more knowledgeable concerning options when we talk solutions.

A little more detail. We...
10-31-16, 05:17 PM
Replies: 18
Views: 688
Posted By ednu99

I'm hoping someone can point me to a type of...

I'm hoping someone can point me to a type of switching system that could be used for HID lighting. We really weren't looking to replace the existing breakers with switchable.
10-31-16, 11:39 AM
Replies: 18
Views: 688
Posted By ednu99

It's a Square D panel and the breakers push in....

It's a Square D panel and the breakers push in. The cabinet face isn't keeping the breakers positioned tightly and as was pointed out the bus bar is probably worn so I'm assuming new switchable...
Showing results 1 to 25 of 142
 


 
Forum Jump