Search: Posts Made By: kumai
Showing results 1 to 25 of 48
Search took 0.01 seconds.
Replies: 4
Views: 1,149
Posted By kumai

possible cam or crank sensor

possible cam or crank sensor
Replies: 12
Views: 792
Posted By kumai

drive the vehicle and try to sway the vehicle...

drive the vehicle and try to sway the vehicle right and left and listen for a change of pitch in noise to isolate if its a wheel bearing and which side
Replies: 2
Views: 2,205
Posted By kumai

i would check the thickness of the rotors, these...

i would check the thickness of the rotors, these rotors are famous for wearing close to the minimum thickness.
Replies: 5
Views: 1,168
Posted By kumai

I would take it back and have them look at it,...

I would take it back and have them look at it, usually dealers will take is as a recheck if it has only been a few months
Replies: 13
Views: 13,723
Posted By kumai

the upper plenum gasket is re-usable. the upper...

the upper plenum gasket is re-usable. the upper water inlet comes with the gasket...you may need new clamps for the coolant hoses that goes to the water inlet. The original ones are a spring type,...
Replies: 13
Views: 13,723
Posted By kumai

just remove the upper intake plenum bolts, and...

just remove the upper intake plenum bolts, and the 13mm under the throttle body you can leave all the wires to the sensors, and the throttle cable connected you just need a little space to get the...
Replies: 6
Views: 8,283
Posted By kumai

one easy way to determine a fuel or ignition...

one easy way to determine a fuel or ignition problem is to shoot carb cleaner into the tb,
Replies: 9
Views: 881
Posted By kumai

the lower control arm bushings are famous for...

the lower control arm bushings are famous for failing, also wheel bearings or sway bar bushings
Replies: 13
Views: 13,723
Posted By kumai

for your vehicle you don't have to remove all...

for your vehicle you don't have to remove all that was said, lust remove the upper intake manifold., the the upper water inlet...takes about 15 minutes or so
Replies: 13
Views: 883
Posted By kumai

youe welcome, re-post what the dealer says

youe welcome, re-post what the dealer says
Replies: 7
Views: 1,645
Posted By kumai

i would remove the panel and with a test light...

i would remove the panel and with a test light check power and ground at the socket connector
Replies: 13
Views: 883
Posted By kumai

sorry to tell you but you have the wrong engine...

sorry to tell you but you have the wrong engine installed...or at least the wrong cam sprocket...there is a certain year that chrysler has change the pcm from sbec to ngc. the cam sprockets have...
Replies: 3
Views: 2,149
Posted By kumai

checked the idler, tensioner and waterpump, I...

checked the idler, tensioner and waterpump, I have changed many alternators in caravans and town and countrys for noise, rattle, knock,
Replies: 7
Views: 1,645
Posted By kumai

have you tried to it with a mobile phone charger,...

have you tried to it with a mobile phone charger, you just need to find wheter it's the dvd cord/plug or the outlet. if it's the oulet it sounds like a fuse, the odds of all the power outlets nt...
Replies: 5
Views: 728
Posted By kumai

which side is smoking, does the car pull to one...

which side is smoking, does the car pull to one side low speeds, did you make sure the pads are in the caliper slides correctly not cocked?? did you forget to put back any caliper slides, anti-rattle...
Replies: 3
Views: 1,844
Posted By kumai

pinion depth is a easy measurement, when you get...

pinion depth is a easy measurement, when you get the new pinion there is a =/- number on the pinion head, you need to mic the old shim and add or sub the difference there is a chart for this. When...
Replies: 13
Views: 883
Posted By kumai

i would try with the cam sensor unplugged crank...

i would try with the cam sensor unplugged crank it for 10-15 secs if it doesn't start. re-post...and we'll investigate further.
Replies: 13
Views: 883
Posted By kumai

why was the engine replaced anyways, have you...

why was the engine replaced anyways, have you tried to remove the cam sensor connector and start the vehicle......I would also try that and let me know.....
02-13-09, 07:46 PM
Replies: 4
Views: 850
Posted By kumai

so what are the tap block used for. I would think...

so what are the tap block used for. I would think it's to run a parallel circuit as to 1 main breaker and 2 panels. I mean it accepts large gauge wires so I figured it's for a main power source
Replies: 1
Views: 903
Posted By kumai

the switch is in the door lock actuator..

the switch is in the door lock actuator..
Replies: 13
Views: 883
Posted By kumai

sorry it's 2 years newer.....I would try and...

sorry it's 2 years newer.....I would try and remove the camshaft sensor connector, the one on the on the front (right side of the engine) and crank the vehicle it may take a long time to start if it...
Replies: 13
Views: 883
Posted By kumai

what year is the used engine???

what year is the used engine???
Replies: 6
Views: 12,668
Posted By kumai

I would perform a visual inspection make sure no...

I would perform a visual inspection make sure no emission vacuum(the diagram should be under you hood) lines are cracked or leaking. make sure you as cap is tight, disconnect your battery and see...
Replies: 12
Views: 25,398
Posted By kumai

if its a wire shorted to ground it should still...

if its a wire shorted to ground it should still start or at least sputter on the 4 cylinders, what about the or/gr wire (I think its the color) it's the asd wire. it should have power for a few secs...
Replies: 13
Views: 883
Posted By kumai

there could be many problems...was the engine new...

there could be many problems...was the engine new or used is the first main question
Showing results 1 to 25 of 48
 


 
Forum Jump