Search: Posts Made By: Hondal
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Replies: 9
Views: 1,528
Posted By Hondal

Thumbs up Finally Figured it all out and it's running now. ...

Finally Figured it all out and it's running now.

What it was is the carb had rust on the float bowel flooding the carb and must have sent gas into the combustion chamber and I sheared the flywheel...
Replies: 9
Views: 1,528
Posted By Hondal

Now do I need a special tool to remove the...

Now do I need a special tool to remove the valves? DO I grind down the end of the actual valve end? I tore the engine down and put it back together without a manual so I am researching all things...
Replies: 2
Views: 866
Posted By Hondal

12.5 B&S Black Coil wire connection

I rebuilt my B%S 12.5 Engine model 282707-0116 and I can't remember where to connect the black wire from the coil. I was able to start it and shut it off by grounding this wire but I need to hook it...
Replies: 9
Views: 1,528
Posted By Hondal

Do I have to tear down the engine to adjust the...

Do I have to tear down the engine to adjust the valve clearance? I had the machine shop adjust the valves and I am not sure if they did a good job. To note when I pull the head off the was some...
Replies: 9
Views: 1,528
Posted By Hondal

12.5hp B&S engine rebuild, engine won't start

Hey I just finshed rebuilding my 12.5 B&S model 282707-0116. It is bored .020 over. I did get it all back together and after finding out the coil was on backwards I got spark and had it Running. I...
Replies: 7
Views: 2,207
Posted By Hondal

Thanks all I got the proper B&S key and yes it is...

Thanks all I got the proper B&S key and yes it is made of aluminum I think so everything is cool thanks again.

Cheers
Al
Replies: 7
Views: 2,207
Posted By Hondal

Thanks to all. I thought the washer was missing...

Thanks to all. I thought the washer was missing cause in the four cylinder repair book they show one but maybe for another model. It looked like i need it but it is not in the illustrated parts...
Replies: 7
Views: 2,207
Posted By Hondal

B&S 12Hp Engine re-build Questions

Got my 12 HP Briggs and Stratton engine back from the machine shop. The Model # is 282707-0116. The engine was bored 0.020" over and I had the valves re-done at the same time. Based on the book i...
Replies: 4
Views: 1,458
Posted By Hondal

Smile I do not have the service manual but did find...

I do not have the service manual but did find some specs off the web. I have been looking for a service manual so I can do more on the engine. If you know where I can get a service manual in PDF...
Replies: 4
Views: 1,458
Posted By Hondal

12 HP B&S cam timing, Engine re-build

1) I took my 12 Hp engine apart and took care to notice the Camshaft timing marks but since the crankshaft is small in diameter than the Camshaft gear when do you line up the dots? I think when the...
Replies: 3
Views: 4,687
Posted By Hondal

B&T 12.5 HP detailed engine schematic re-build

Hey all. I have a 12.5 Briggs and Stratton (engine Series 281707 0116-01)that had low compression 60 psi and I have taken it out and about to start to tear it down. I found a schematic online but...
Showing results 1 to 11 of 11


 
Forum Jump