Search: Posts Made By: cuda clan
Showing results 1 to 25 of 30
Search took 0.01 seconds.
Replies: 2
Views: 909
Posted By cuda clan

Lightbulb Welding school's?

I'm in my senior year of a technical high school and I'm wondering about my continued education (parents can't wait for me to leave ;)). My school follows the Miller SENSE program that includes every...
01-08-05, 07:28 PM
Replies: 2
Views: 902
Posted By cuda clan

If the project is large consider metal laminated...

If the project is large consider metal laminated products. Yes, it is also made in stainless steel, aluminum & copper. To obtain the “fish scale” effect, purchase an abrasive disc from an automotive...
Replies: 3
Views: 1,088
Posted By cuda clan

The correct location of the set timing connector...

The correct location of the set timing connector is inside the cab where the heater box and the carpet meet on the passenger side floor. Pull carpet back to expose the single wire and connectors on...
Replies: 2
Views: 967
Posted By cuda clan

I have had the same experience with my van as...

I have had the same experience with my van as well, same application but a 93' year. I found the (redundant) ground cable behind the battery had lost "contact" with the inner wheel well. There is a...
Replies: 1
Views: 1,109
Posted By cuda clan

If the vehicle has a bent hub bearing it would...

If the vehicle has a bent hub bearing it would give the same sensation as a warped rotor/drum. A dial indicator is needed for this. Before you condemn any part, diagnose. On an "empty" road...
Replies: 14
Views: 8,025
Posted By cuda clan

I think this is an Ohm's Law problem. "One...

I think this is an Ohm's Law problem.

"One thing I did notice, but not extremely bad, was the negative terminal on the battery was warm."

The neg. - cable will be warm if excessive cranking was...
Replies: 4
Views: 1,217
Posted By cuda clan

After it is said & done, don't use bolts, use...

After it is said & done, don't use bolts, use studs as replacements.
07-15-04, 05:25 PM
Replies: 6
Views: 15,823
Posted By cuda clan

This link should help, use the products listed...

This link should help, use the products listed under Leaf Hoppers, try the sequence of pesticides listed for eradication. The insecticidal soap is less toxic (try this method first, it is more...
07-14-04, 07:44 PM
Replies: 6
Views: 15,823
Posted By cuda clan

Yes, start with a less toxic control. Hoppers...

Yes, start with a less toxic control. Hoppers prefer a greener lawn, the results are toxins released from them by eating the lawn and the grass blades suffer. It's not their consumption from eating ,...
07-13-04, 04:05 PM
Replies: 6
Views: 15,823
Posted By cuda clan

Leafhoppers are my guess. Tank or hose spray...

Leafhoppers are my guess. Tank or hose spray application with pesticide of choice should do it.
07-13-04, 02:33 PM
Replies: 2
Views: 802
Posted By cuda clan

Make certain that the compost pile reaches...

Make certain that the compost pile reaches optimum temperature and has completely broken down. If this is not done, you will regret the seedlings that germinate.
07-07-04, 04:20 PM
Replies: 2
Views: 2,868
Posted By cuda clan

What an attractive Art-Deco concept. Please...

What an attractive Art-Deco concept. Please consider that rope lights do not have a long “bulb” life. Stated, make it accessible to replace the lighting. Is it possible to create a wall cavity for...
Replies: 9
Views: 9,009
Posted By cuda clan

"Kill two birds with one stone", replace pan &...

"Kill two birds with one stone", replace pan & gaskets.
That statement about the crank wearing out the seal is off. Ask yourself, how many miles was placed on the original seal, not one year! If you...
Replies: 9
Views: 9,009
Posted By cuda clan

Don't these oil pans have a history of rusting...

Don't these oil pans have a history of rusting out ?
I have seen and replaced many, trucks & vans mostly.
Check for blistering of metal/paint from the pan.
Replies: 5
Views: 1,005
Posted By cuda clan

Could be a problem if tilt steering (specialty...

Could be a problem if tilt steering (specialty tool). If vehicle was from a previous theft/damage (not stated) a "kit" is available with steering collar, rack,...
08-29-03, 04:09 PM
Replies: 13
Views: 20,704
Posted By cuda clan

This tank does not seem to be the "run of the...

This tank does not seem to be the "run of the mill" size. This will be a custom tank & install I presume. In order for it to fit in a wall, the tank will have to be in proportion to the wall. If this...
08-28-03, 09:30 PM
Replies: 13
Views: 20,704
Posted By cuda clan

Though it is pleasing to the eye, this tank...

Though it is pleasing to the eye, this tank set-up is unhealthy for any fish. Think of it, the walls (in general) are to be based on 2x4's. It's like watching a tiger in a cage that is small. There...
Replies: 3
Views: 2,236
Posted By cuda clan

This is the dealership, it may be correct. Don't...

This is the dealership, it may be correct. Don't forget, it is all a one piece unit. Normal R&R would be to cut the cat(s) from the pipes and weld/clamp replacements. I don't think this is a single...
Replies: 14
Views: 31,825
Posted By cuda clan

If fuse(s) are not blown, you have an open...

If fuse(s) are not blown, you have an open circuit. In other words, the wire that powers those items has no connection to them from the source of power. Time to "chase" wires.
Replies: 5
Views: 854
Posted By cuda clan

The oil pans are known to rust through on the...

The oil pans are known to rust through on the tucks/vans. Replace the pan with the seal. It might even be the pan, if so less work.
Replies: 7
Views: 712
Posted By cuda clan

Drives kinda fast, hmmm... there is a moral here....

Drives kinda fast, hmmm... there is a moral here. You tend to appreciate the things you work for.
Replies: 10
Views: 1,757
Posted By cuda clan

Did this problem happen after the thermostat R&R?...

Did this problem happen after the thermostat R&R? If so, the coolant system was not bled. There is a speciel "bleeder screw" on the thermostat housing to do so. Yes this will set the coolant and...
Replies: 2
Views: 691
Posted By cuda clan

Common problem, replace them and don't think of...

Common problem, replace them and don't think of having them welded.
Replies: 10
Views: 935
Posted By cuda clan

It is possible to see all data from the OTC,...

It is possible to see all data from the OTC, Snap-On, etc scanners.
Most have the ability to capture a 'snap-shot" of a problem to observe on a PC. A seperate software is available from the...
Replies: 2
Views: 686
Posted By cuda clan

It is also normal for it to cycle in the defrost/...

It is also normal for it to cycle in the defrost/ defog mode.
Showing results 1 to 25 of 30
 


 
Forum Jump