Search: Posts Made By: jmm706
Showing results 1 to 25 of 77
Search took 0.01 seconds.
Replies: 21
Views: 22,876
Posted By jmm706

Good Idea

Good idea. I bought a new Chevy once a long time ago that quit on the way home from the dealer. Saturday and they are now closed, I stuck a golf tee in the vacuum line to EGR valve. It stayed that...
Replies: 21
Views: 22,876
Posted By jmm706

The Saga Continues...

I have verified that the "Check Engine" light comes on within a second or two after the engine dies, the same result as turning off the key produces. I've also noticed that that if in gear idling at...
Replies: 21
Views: 22,876
Posted By jmm706

Scan Results

I put my newly purchased scanner on the Crown Vic. It passed with flying colors. No codes or even pending codes! I knew this wasn't going to be easy. The last time I drove the car, it ran great...
Replies: 21
Views: 22,876
Posted By jmm706

Good Ideas

Thanks for the good ideas. I've ordered a scanner. I've been needing one anyway. I looked at the IAC, it looks brand new, not dirty a bit. It must have been changed. The throttle body is as...
Replies: 21
Views: 22,876
Posted By jmm706

Thanks

I'll try some of those ideas. I feel like if I could just raise the idle a little bit it might be OK, but I guess the comptuer isn't going to allow mw to do that.
Replies: 21
Views: 22,876
Posted By jmm706

More Info

The car will start right up with no problem after it dies. I did some research with others who have driven this car and according to the original driver the car has done this since new! I can't...
Replies: 21
Views: 22,876
Posted By jmm706

Crown Vic Dies at a Light

2003 Ford Crown Vic Police Interceptor. 113K miles. Engine runs great and strong. Idles smooth in park for hours. Maybe twice in 12 hours while sitting at a stop light, the engine will just die. ...
Replies: 11
Views: 14,087
Posted By jmm706

Hose

Sounds like you may have a rat visting. Your idea of slipping something over the hose to armor clad it is a good one. I had a rat make a nest in a brand new car one time. The dealer found it on a...
Replies: 8
Views: 1,318
Posted By jmm706

Rpm

Glad i'ts fixed!
Replies: 17
Views: 16,791
Posted By jmm706

Bypass

The part is the vacuum control valve that allows water to circulate through the heater core and provide heat to the interior of the car.
Replies: 4
Views: 1,097
Posted By jmm706

Zone Descriptors

Any ideas on how to enter zone descriptors?
Replies: 4
Views: 1,097
Posted By jmm706

Zone Descriptors

My bad. I said 6150, I meant 6160. I have the alpha keypad.
Replies: 4
Views: 1,097
Posted By jmm706

Alpha Nightmare

I'm having trouble setting word descriptions of my zones on my Ademco Vista 10se and 6150 keypad. I have both manuals. After entering *82 and answering the custom yes/no prompt, it takes me to zone...
Replies: 6
Views: 1,642
Posted By jmm706

Brake Light

You are correct in that there is no shim installed in your hand brake assembly. However, the repair manual warns to insert a home made shim or spacer in between the lever and the assembly before you...
01-13-07, 02:57 PM
Replies: 4
Views: 1,607
Posted By jmm706

Pin hole Copper Leaks in Slab

If the floor is warmer than the rest of the floor for no other apparent reason, you may have a leak. Turn all the water off in your house (even the icemaker) and read the meter. Let an hour go by...
Replies: 6
Views: 1,642
Posted By jmm706

Brake Light

Have you had the right throttle/hand brake assembly off the handle bars lately? If you don't put a shim in the brake lever assembly before you take it off you can permanently damage the brake light...
Replies: 6
Views: 2,273
Posted By jmm706

Thermostat

If you follow the uppermost hose from the radiator to the engine, the thermostat will be under that housing. Drain the old coolant by opening the petcock at the bottom of the radiator. You will...
Replies: 1
Views: 904
Posted By jmm706

6160 Addressable?

I took advise I got here and ordered an Ademco 6160 keypad for my Vista 10se system. I haven't had time to install it yet, but I did read through the instruction sheet that came with it. It...
Replies: 2
Views: 1,041
Posted By jmm706

6160v

Thanks, I think I'll just opt for the regular 6160 key pad.
Replies: 2
Views: 1,041
Posted By jmm706

Vista-10 With 6160V Panel

I have been told that a Ademco 6160V (voice) keypad will work with my Vista-10 alarm. (I'm upgrading the keypad to be able to program the system.) Someone just told me that although the 6160V will...
Replies: 2
Views: 837
Posted By jmm706

Thanks

I'll give that a try when the time comes.
Replies: 2
Views: 837
Posted By jmm706

Lock Out Company

My security monitoring contract will be up in a few months and I am considering switching to another company. I own the Ademco Vista 10 equipment. Is there a programming step I can take to keep the...
Replies: 1
Views: 960
Posted By jmm706

6160V Application

I have an Ademco Vista 10 panel. I have an opportunity to buy a 6160V keypad. Will that keypad wotk with the Vista 10 panel to program it as well as use the voice feature?
05-11-06, 09:53 AM
Replies: 1
Views: 735
Posted By jmm706

Is This A Keeper?

New house. Shutoff valves all look like this. I'm wary of the plastic tubes and plan to replace them. But, anyone familiar with this type of valve? Any good?
...
Replies: 1
Views: 4,619
Posted By jmm706

Drawer Pull Repair Question

I have a metal drawer pull about 5 or 6 inches wide that the small pivot end hads broken off. The pull is an antique brass finish, but almost looks like some kind of casting from the back unfinished...
Showing results 1 to 25 of 77
 


 
Forum Jump