Search: Posts Made By: jjudson
Showing results 1 to 17 of 17
Search took 0.01 seconds.
01-03-18, 05:37 AM
Replies: 9
Views: 644
Posted By jjudson

Allanj, would you mind providing more detail on...

Allanj, would you mind providing more detail on your neutral line management post? I'm curious to learn more. Why wouldn't you tie all the neutrals together? Don't they all go back to the same place?
01-02-18, 09:14 AM
Replies: 9
Views: 644
Posted By jjudson

Multiwire Connection - sort of...

I am moving my kitchen from one room to another. I need to move the electrical connections, too. I have a question about a particular outlet box:

If a box has two outlets that are served by two...
Replies: 3
Views: 616
Posted By jjudson

Thanks PJmax. Inside the unit, there's a daughter...

Thanks PJmax. Inside the unit, there's a daughter board that seems to contain the comm electronics and SIM card. I'm wondering if swapping that board and SIM card would work -- and more importantly,...
Replies: 3
Views: 616
Posted By jjudson

Convert GSMV4G to work with Verizon

I have a GSMV4G panel that is set for ATT networks. Unfortunately where I moved, ATT is not available. Verizon is the main system. Can the communications module or any component be switched to...
Replies: 2
Views: 863
Posted By jjudson

Disregard

Never mind. Found answer.
Replies: 2
Views: 863
Posted By jjudson

Ran out of wireless zones! Vista 20P

Okay, another set of questions with my Vista 20P:

The panel specs say the unit will handle 40 wireless zones, but I guess if you have a 6150RF keypad, that 40 goes down to 16? I wonder because I...
Replies: 8
Views: 9,810
Posted By jjudson

ChosunOne, I changed the loop numbers to 2 and...

ChosunOne, I changed the loop numbers to 2 and now the system is working properly. I checked the documentation for the sensors, and there's no mention of the proper loop number in it. Curious. I wish...
Replies: 8
Views: 9,810
Posted By jjudson

ChosunOne, the window and door sensors were left...

ChosunOne, the window and door sensors were left in place by the previous owner, so I didn't have the documentation (I probably could have found it somewhere online I guess). I'll try changing the...
Replies: 8
Views: 9,810
Posted By jjudson

Vista 20P Faults Won't Clear

I've just gotten my Vista 20P panel and 6160 and 6150RF keypads set up and I'm running into a problem. I have all-wireless sensors, mostly consisting of 5816 sensors. Problem now is, the faults...
Replies: 7
Views: 779
Posted By jjudson

Okay, and one last question MrRonFL before I let...

Okay, and one last question MrRonFL before I let you go: I take it you need a separate zone for each wireless device? Can you put more than one in each zone like you can with wired?

Thanks for...
Replies: 7
Views: 779
Posted By jjudson

MrRonFL, you are my hero... Is there a place...

MrRonFL, you are my hero...

Is there a place that describes the various loop numbers and what they are used for?

Also, would the loop number 1 that the smoke detectors are on be correct for...
Replies: 7
Views: 779
Posted By jjudson

MrRonFL, actually, you're right, the keypad is a...

MrRonFL, actually, you're right, the keypad is a 6160 and the other a 6150RF. The loop number of the smoke detectors on Zone 09 and 10 are both 1. The loop number on the Entry/Exit #1 sensor is 4. ...
Replies: 7
Views: 779
Posted By jjudson

Sensors not working right - Vista 20P

I've reinstalled my Vista 20P panel into my new home, and I'm only using wireless sensors for this installation. I've gone through the setup procedure. The 6150 and 6150RF panels seem to be working...
02-20-14, 03:43 AM
Replies: 6
Views: 962
Posted By jjudson

Furd, it might be easier to run cable instead of...

Furd, it might be easier to run cable instead of conduit behind the wallboard. It's tight back there.
02-20-14, 03:37 AM
Replies: 6
Views: 962
Posted By jjudson

Ray2047, I'm running a neutral as there's a...

Ray2047, I'm running a neutral as there's a control panel that manages the 240 load that runs on 120.
02-19-14, 06:17 PM
Replies: 6
Views: 962
Posted By jjudson

Hookup wire vs NM-B behind walls

I ran four separate 10 gauge 600 volt PVC insulated wires through conduit from one side of my garage to a junction box near my panel for a 220 VAC power source I need. I need to go from the junction...
Replies: 1
Views: 1,072
Posted By jjudson

Question Zone Configuration Question

Maybe I'm overthinking this, but tell me what's right here. I'm setting up a Vista 20P panel and configuring the zones. I'm using NC contacts for the system. Three programming items I'm wondering...
Showing results 1 to 17 of 17


 
Forum Jump