Search: Posts Made By: w3412
Showing results 1 to 17 of 17
Search took 0.01 seconds.
Replies: 5
Views: 493
Posted By w3412

Thank you all for your expert info. The best...

Thank you all for your expert info.
The best solution is replace it with a high security new lock.
Replies: 5
Views: 493
Posted By w3412

Add photo

Here is the photo of the lock.
Replies: 5
Views: 493
Posted By w3412

Legacy door lock

I have this old lock - you use key to turn the core and then push the lever to activate the latch.
First the lever was sluggish and stuck, a little bit of WD-40 did loose it. But this time it won't...
Replies: 5
Views: 474
Posted By w3412

Thank you all, will follow your order.

Thank you all, will follow your order.
Replies: 5
Views: 474
Posted By w3412

Thumbs down Glacier Bay Faucet failed

It has two 90 degrees valve handles.
It seals OK if no water on.
once cold or hot or both on, immediately, drips started under the sink, but no sign above the sink.
Removed the faucet from the...
07-31-18, 09:53 AM
Replies: 1
Views: 422
Posted By w3412

Wavetek 27XT meter: fail Cx

Hi,

This meter works fine except for Cx. Any thought?
TIA
07-29-18, 07:14 PM
Replies: 7
Views: 977
Posted By w3412

I will clean the connectors, using the kit...

I will clean the connectors, using the kit recommended by Houston204.
Thanks to both of you.
07-29-18, 05:11 PM
Replies: 7
Views: 977
Posted By w3412

In the early post I thought the connectors were...

In the early post I thought the connectors were rusted, they could be burnt with the sign of black mark. So this is not the first time.
07-29-18, 04:48 PM
Replies: 7
Views: 977
Posted By w3412

Locked Compressor?

This is a continuation of
Bristol compressor test /wiring
https://www.doityourself.com/forum/search.php?searchid=2040572

For Bristol compressor Model H29B35Uabca. The new problem

The correct...
07-17-18, 03:46 PM
Replies: 7
Views: 977
Posted By w3412

Hi Houston204: Your description matches the...

Hi Houston204:

Your description matches the chart.
Thank you,
07-16-18, 01:22 PM
Replies: 7
Views: 977
Posted By w3412

Bristol compressor: test/wiring - locked compressor?

This one is of Model H29B35Uabca, not running. found wiring problem: Of the three leads, red still attached to, Black detached and yellow lost the connector. It seemed the corrosion rusted the lead...
09-07-17, 08:54 PM
Replies: 4
Views: 2,986
Posted By w3412

Hi Goldstar and Pjmax, The pump is relatively...

Hi Goldstar and Pjmax,
The pump is relatively new, no rust, no dry leather piston. The pump can pump and hold up to 75 psi, but no air out passing that valve.
The outer steel housing pipe and the...
09-07-17, 05:59 PM
Replies: 4
Views: 2,986
Posted By w3412

Photo Attachment

showing the housing with the plunger and air hose removed, the only part therein is the check valve behind the brass fitting.
09-07-17, 05:49 PM
Replies: 4
Views: 2,986
Posted By w3412

MaxAir bicycle pump valve problem

The valve at the bottom of the pump seemed blocked, can hardly pump air in.
I tried to detach the air hose and no air can reach that point,
Here may not be the right place, but please help me to...
12-22-12, 09:57 AM
Replies: 3
Views: 4,676
Posted By w3412

Yes. The temperature control is OK, only...

Yes. The temperature control is OK, only complaint is about the shut off, as the pipe behind the wall is not completely fixed, but hanging from above, so the shutting would cause the tub faucet...
12-20-12, 07:15 AM
Replies: 3
Views: 4,676
Posted By w3412

Exclamation Symmons shower/tub valve extremly hard to fully shut OFF

I read some old thread about the same problem, all seems as
a simple issue. But it is not.

The problem is: the valve was turned to the full OFF, but the water still drip.
You could turn the...
12-20-12, 07:09 AM
Replies: 3
Views: 9,359
Posted By w3412

symmons' sysmatic error?

The same problem here.
The valve was turned to the full OFF, but the water still drip.
You could finally SHUT it off, but the effort is terrible. The whole
base was shaked away from the installed...
Showing results 1 to 17 of 17


 
Forum Jump