Search: Posts Made By: sdsdogg2
Showing results 1 to 25 of 46
Search took 0.02 seconds.
Replies: 2
Views: 860
Posted By sdsdogg2

You will need to take off the axle nut with a...

You will need to take off the axle nut with a 36mm socket and breaker bar. Hold the hub from rotating by some one holding the brakes or a large screw driver between the roter venbt fins and calper...
Replies: 7
Views: 2,102
Posted By sdsdogg2

Yes, the lash should be .010 intakes and .012...

Yes, the lash should be .010 intakes and .012 exhaust. Engine temp cold.
Replies: 2
Views: 892
Posted By sdsdogg2

Soak the brake line nut with penatrating oil and...

Soak the brake line nut with penatrating oil and use a line nut not an open end wrench to losen the nut. If the brake fluid soaked into the shoes they also must be replaced. If the springs are rusty...
Replies: 2
Views: 1,590
Posted By sdsdogg2

This means that you cat converter is not working...

This means that you cat converter is not working properly . You should check for an exhaust leak before the post cat o2 sensor. However this code is a 3 trip failure and most of the time it is the...
Replies: 6
Views: 994
Posted By sdsdogg2

Ford makes the best trucks

Ford makes the best trucks
Replies: 6
Views: 1,035
Posted By sdsdogg2

Ford does not recomend cleaning their throttle...

Ford does not recomend cleaning their throttle bodys due to a coating inside. Does the car seem to run rich or does it idle ok?
Replies: 4
Views: 1,061
Posted By sdsdogg2

I am assuming that the oil gauge in the car is...

I am assuming that the oil gauge in the car is aftermarket. If the hose is a clear plastic tube than you can buy the hose and ferrals as a kit at any part store. I have seen them at Auto Zone,...
Replies: 5
Views: 769
Posted By sdsdogg2

Thank you for all the help guys

Thank you for all the help guys
Replies: 5
Views: 769
Posted By sdsdogg2

72 mustang

I have a 72 mustang convertable. I am looking for a grill and all I seem to find are 73 mach 1 grills. Does anyone know if this will work? They look different in size and shape. It seems that 71 and...
Replies: 23
Views: 1,515
Posted By sdsdogg2

As compared to a copper electroid the one platnum...

As compared to a copper electroid the one platnum center electroid (the one that mostly wears) last longer
Replies: 23
Views: 1,515
Posted By sdsdogg2

If you had a problem with bosch platnum than you...

If you had a problem with bosch platnum than you used the wrong ones
Replies: 23
Views: 1,515
Posted By sdsdogg2

Do you concider 1.99 bosch platnum plugs as high...

Do you concider 1.99 bosch platnum plugs as high dollar?
Replies: 23
Views: 1,515
Posted By sdsdogg2

My 2 cents. I have used Bosch platnums on all...

My 2 cents. I have used Bosch platnums on all makes and modles for about three years and never had a problem. Through the years I had problems with ac delco on gm autolites on fords and especaly...
Replies: 9
Views: 5,809
Posted By sdsdogg2

Pull the abs fuse for one min.

Pull the abs fuse for one min.
Replies: 9
Views: 973
Posted By sdsdogg2

I do remerber there was a bulleten on this...

I do remerber there was a bulleten on this problem and it had something to do with the powerstering pressure hose when cold. If no belt problem i would check for tsb's
Replies: 19
Views: 4,392
Posted By sdsdogg2

You can rock the belt back and forth and watch...

You can rock the belt back and forth and watch the pulley move without the crank moving. All of the dampners i have seen were not encased in metal
Replies: 3
Views: 1,929
Posted By sdsdogg2

The ball joints come out with the hub. The most...

The ball joints come out with the hub. The most time consuming part is to remove the Rotor and spindle asm. Than pull the axle out and remove the tie rod end fron knuckle . Remove the upper and lower...
Replies: 27
Views: 1,290
Posted By sdsdogg2

It is on the side of the tranny near the pan from...

It is on the side of the tranny near the pan from under the car
Replies: 6
Views: 832
Posted By sdsdogg2

I would guess its a 3.1 and you replaced the...

I would guess its a 3.1 and you replaced the crank becouse it spun a brg. (another GM boat ancor). The crank has a crankshaft position sensor reluctor ring on it. Did the new one have it on and was...
Replies: 27
Views: 1,290
Posted By sdsdogg2

No the problem sounds just like a torque...

No the problem sounds just like a torque converter clutch that wont disengauge. Try to unplug the 4 wire connector on the tranny and redrive. If the problem goes away than you most likely need a tcc...
Replies: 10
Views: 1,048
Posted By sdsdogg2

Eproms can be checked for updates online @...

Eproms can be checked for updates online @ http://calid.gm.com/vci/ All you need is the VIN #

Your problem sounds like an ignition switch problem . Is there 10 lbs of keys on the ring? This wipes...
Replies: 9
Views: 1,992
Posted By sdsdogg2

Oh by the way the sox looked good this weekend...

Oh by the way the sox looked good this weekend (1918)
Replies: 9
Views: 1,992
Posted By sdsdogg2

Its easy . Flip the car on its roof and pour it...

Its easy . Flip the car on its roof and pour it into the hole in the bottom of the bellhousing while cranking the engine over for proper distrabution, This should only be performed by professionals:D
Replies: 7
Views: 1,146
Posted By sdsdogg2

Hold on Kim. I dont think you will have a shrader...

Hold on Kim. I dont think you will have a shrader port on your fuel rail and 40 psi sounds like a lot. Consult a service manual or as Joe would say check out Alldata for proper proceduer
Replies: 3
Views: 1,010
Posted By sdsdogg2

How does it die? Does it shut off quick like...

How does it die? Does it shut off quick like turning off the key or does it buck or pop? I have seen ignition switch problems on some of these where the power is lost to the pgm relay. There is a tsb...
Showing results 1 to 25 of 46
 


 
Forum Jump