Search: Posts Made By: bajrah
Showing results 1 to 13 of 13
Search took 0.01 seconds.
01-11-11, 08:11 AM
Replies: 4
Views: 774
Posted By bajrah

This installation is outside the wall and has...

This installation is outside the wall and has already been glued together and attached to the wall. So moving it around is not quite possible.

I will post some pictures later.
01-11-11, 06:29 AM
Replies: 4
Views: 774
Posted By bajrah

Plumbing question.

I just finished putting together a drain in my laundry room for my washer and utility sink.

I had everything cut to size and marked for fall requirements. But when I cemented the joints the fall...
12-15-10, 06:54 AM
Replies: 4
Views: 1,428
Posted By bajrah

What about a thin coat of liquid nails or some...

What about a thin coat of liquid nails or some other type of adhesive?
12-13-10, 08:51 AM
Replies: 4
Views: 1,428
Posted By bajrah

USG Fiberock and vinyl tiles

I used a couple of 1/4x3x5 USG Fiberock sheets on a wall behind a utility sink in my laundry room. I tried sputting vinyl peel and stick tiles on the boards but they don't stick. I also tried an...
12-07-10, 02:15 PM
Replies: 8
Views: 1,130
Posted By bajrah

Thanks for your response. This clears things a...

Thanks for your response. This clears things a lot.
12-07-10, 11:16 AM
Replies: 8
Views: 1,130
Posted By bajrah

There are articles and diagrams on some websites...

There are articles and diagrams on some websites that suggest, ground in the GFCI receptacle does not have to be connected when wiring multiple receptacles protected by one GFCI.

One example is...
12-07-10, 08:37 AM
Replies: 8
Views: 1,130
Posted By bajrah

Yes. As I said I am using 12/2 with ground which...

Yes. As I said I am using 12/2 with ground which will have the ground wire connected to the bus bar in the service panel.
12-07-10, 08:09 AM
Replies: 8
Views: 1,130
Posted By bajrah

GFCI wiring question

I am wiring a new 20amp circuit in my laundry which will have 1 GFCI with 3 regular receptacles downstream.

I am not sure if the ground connection in the GFCI should be bypassed or connected. I...
11-17-10, 09:32 AM
Replies: 11
Views: 1,729
Posted By bajrah

Thanks for the responses. I guess I need to make...

Thanks for the responses. I guess I need to make a plan and get started. But, surely there will be more questions to come.
11-17-10, 08:26 AM
Replies: 11
Views: 1,729
Posted By bajrah

With this new circuit, do I need only 1 GFCI for...

With this new circuit, do I need only 1 GFCI for all the outlets?
11-17-10, 06:55 AM
Replies: 11
Views: 1,729
Posted By bajrah

To answer both questions. The furnace does...

To answer both questions.

The furnace does have a label that says 36" clearance on the front side. I looked up the codes and 3" is required on the back and the sides. Which is good because that...
11-13-10, 07:00 AM
Replies: 11
Views: 1,729
Posted By bajrah

Thanks for the responses. Here's a lilttle more...

Thanks for the responses. Here's a lilttle more info about the room.

1. The washer and dryer are stackable front loading type but I will be putting them next to each other. I will eventually be...
11-12-10, 04:07 PM
Replies: 11
Views: 1,729
Posted By bajrah

Laundry room wiring

I have an unfinished room in my basement which contains the electric water heater and electric furnace. The room is about 12'x8'. My washer and dryer are in a closet next to this room. I would like...
Showing results 1 to 13 of 13


 
Forum Jump