Search: Posts Made By: pugsl
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Today, 09:08 AM
Replies: 4
Views: 85
Posted By pugsl

1st place I would look is the last outlet you...

1st place I would look is the last outlet you plugged into or the one you unplugged. Take outlet out of wall and move any back stabbed wires to screws. If there are wire nuts in there take apart be...
Replies: 6
Views: 243
Posted By pugsl

Be sure to get alignment after boot is installed....

Be sure to get alignment after boot is installed. Will never get tie rod adjusted right after taking off. Check for sand or dirt on shaft, if there sand will get into seal and rack will leak. Than...
Forum: Water Heaters
08-03-20, 08:43 AM
Replies: 10
Views: 140
Posted By pugsl

My water heater is from 69. Wrote company to find...

My water heater is from 69. Wrote company to find out age.Was installed when house built. Afraid to touch it or do any anode rod change. WH looks like it has never been touched. Am budgeting for a...
Replies: 2
Views: 114
Posted By pugsl

model # also, What are you trying to do?

model # also, What are you trying to do?
07-30-20, 05:07 PM
Replies: 5
Views: 145
Posted By pugsl

Best way is to cut a bigger slab out, be sure to...

Best way is to cut a bigger slab out, be sure to cut mid stud so you have nailer. On something like that the bigger the replacement drywall is the cleaner it will look.
07-30-20, 04:59 PM
Replies: 5
Views: 145
Posted By pugsl

2 ways I can think of. both will need drywall...

2 ways I can think of. both will need drywall repair. Putty knife behind mounts and pry out. Second way is a hammer and break them.
07-28-20, 03:20 PM
Replies: 5
Views: 144
Posted By pugsl

You will need a volt meter to be sure.

You will need a volt meter to be sure.
07-28-20, 03:34 AM
Replies: 14
Views: 205
Posted By pugsl

I built a outside work table over 10 years ago...

I built a outside work table over 10 years ago and used azetec ( composite roof board) and used oil poly for outside, Table still there with heavy use. Sold house and last year and buyer eyes lit up...
07-27-20, 03:20 AM
Replies: 10
Views: 234
Posted By pugsl

Not needed but I always put a note with dead...

Not needed but I always put a note with dead wiring to say it id dead and if I know where it goes to tell where the other end is.
Replies: 5
Views: 165
Posted By pugsl

Can't be to much help since I have never seen...

Can't be to much help since I have never seen your type washer but worked on washers for mwny years. I just looked through manual Pete left and page 15 has things about belt.Also check if the hangers...
Replies: 5
Views: 165
Posted By pugsl

Even before I retired we did not work on those...

Even before I retired we did not work on those washers so I have no experience on them. I agree with Pete sounds like something not put together right.
Replies: 6
Views: 126
Posted By pugsl

Not electrician so just a couple of questions to...

Not electrician so just a couple of questions to help clarify. 1 are the pool, pond lights powered off the same circuit in box? Are the flood lights on the single black, white cable or on the red,...
07-24-20, 11:17 AM
Replies: 3
Views: 93
Posted By pugsl

Sounds like you have miss installed a part or...

Sounds like you have miss installed a part or something broken in head.
07-24-20, 08:41 AM
Replies: 12
Views: 264
Posted By pugsl

When you cut out drywall make sure you cut enough...

When you cut out drywall make sure you cut enough to find source of water. If you don't find leak now it will happen again.Even if a wet floor caused it should not of had enough water going through...
07-24-20, 08:36 AM
Replies: 3
Views: 93
Posted By pugsl

Found a page of info on your sprinkler, here it...

Found a page of info on your sprinkler, here it is
https://www.google.com/search?client=firefox-b-1-d&q=rain+bird+5000+manual
Replies: 2
Views: 146
Posted By pugsl

Moved post from gas to electric. When you...

Moved post from gas to electric.
When you cleaned pump did you take it out or just clean filter? Sounds like something jammed in pump or impeller detached from shaft.
Replies: 5
Views: 92
Posted By pugsl

Will give it a few weeks to dry and see what kind...

Will give it a few weeks to dry and see what kind of board it is. Just guessing it was particle board.but did n ot get a good look at it. Just know it was wet and sorta looked like particle board....
Replies: 5
Views: 92
Posted By pugsl

Damp mushy Particle board

New to me house, Finally got up to clean gutters around enclosed patio.. Guess was years since they were cleaned and water backed up into the edge of under layment of roof. Is a rubber membrane over...
07-20-20, 05:40 AM
Replies: 3
Views: 87
Posted By pugsl

Been a long time since I took one apart but...

Been a long time since I took one apart but trying to remember. There are to spring clips in top bottom panel. Push a stiff putty knife in between panel and front, Be sure you are on to[p of clip as...
Replies: 4
Views: 143
Posted By pugsl

Take the front off, 2 clips a putty knife pushed...

Take the front off, 2 clips a putty knife pushed between top and front. Front will come off. Support tub from moving a lot, Pete's suggestion is good. I would wrap 2X4 with towels. Much better...
Replies: 4
Views: 165
Posted By pugsl

Never ever even thought to try to clean a spark...

Never ever even thought to try to clean a spark arrestor. Never had a problem with one either.
07-17-20, 11:18 AM
Replies: 2
Views: 217
Posted By pugsl

thumping noises are caused by a flat spot on...

thumping noises are caused by a flat spot on roller or something stuck on belt or roller. Don't think lube will help. May need a new belt.
07-16-20, 05:17 PM
Replies: 6
Views: 184
Posted By pugsl

Just go to your friendly Hardware,Lowes or HD and...

Just go to your friendly Hardware,Lowes or HD and in plumbing section there will be complete 1/4 inch shut offs. All you will need is a tubing cutter to do the job. Was a auto mechanic for many years...
Replies: 8
Views: 182
Posted By pugsl

Some sort of alignment issue and possible balance...

Some sort of alignment issue and possible balance also. Vibration could of been road. but if continues I would get all 4 wheels re balanced.
Replies: 13
Views: 381
Posted By pugsl

That means that it is a air tube. No electric...

That means that it is a air tube. No electric under there just the tube connected to internal pressure switch. Take it out and vent may shut off. If contacts are welded shut than it will stay running...
Showing results 1 to 25 of 200
 


 
Forum Jump