Search: Posts Made By: cmw0021
Showing results 1 to 25 of 30
Search took 0.01 seconds.
Replies: 6
Views: 7,191
Posted By cmw0021

sounds like sucking air. check for broken...

sounds like sucking air. check for broken gaskets. make sure your carb is tight
Replies: 6
Views: 1,049
Posted By cmw0021

i agree, dont get rid of it. but if you really...

i agree, dont get rid of it. but if you really want to, here is a great mower that will last many years with no problem, and even has self propelled. i have this model but non-propelled. runs great,...
Replies: 6
Views: 1,420
Posted By cmw0021

ok, thanks for the info

ok, thanks for the info
Replies: 6
Views: 1,420
Posted By cmw0021

its a 7hp motor, its from a friends lawnmower.

its a 7hp motor, its from a friends lawnmower.
Replies: 6
Views: 1,420
Posted By cmw0021

vertical engine for go kart?

is it possible to have a vertical engine put on a go-kart with a pulley? if so, where could i find these certain pulleys?
Replies: 10
Views: 3,958
Posted By cmw0021

i read about valves not closing properly due to a...

i read about valves not closing properly due to a few causes. and a mecanical failure in the carb (for the carb to smoke) but yes the oil is milky and exhaust is ran through the oil tube.
Replies: 10
Views: 3,958
Posted By cmw0021

ok no problem. but yeah i cleaned the whole card...

ok no problem. but yeah i cleaned the whole card and took out that problem seal, but didnt have another so i didnt replace it. its a b***h to get started and keep running, but once warm it is...
Replies: 10
Views: 3,958
Posted By cmw0021

well maybe, but so u say i know the solution? and...

well maybe, but so u say i know the solution? and what may it be? i really just want to learn, i have 2 mowers as it is and a brand new 5.5hp honda mower, so i dont need it. if you do know what to do...
Replies: 10
Views: 3,958
Posted By cmw0021

barely runs, itll only keep running when fully...

barely runs, itll only keep running when fully warmed. im going to try and swap my old craftsman 3.5 mower engine, to the craftsman 6.75 only because it runs.
Replies: 10
Views: 3,958
Posted By cmw0021

barely runs, itll only keep running when fully...

barely runs, itll only keep running when fully warmed.
Replies: 10
Views: 3,958
Posted By cmw0021

it looked like a cloud of exhaust, i hardly saw...

it looked like a cloud of exhaust, i hardly saw any comming out of the exhaust pipe LOL
Replies: 10
Views: 3,958
Posted By cmw0021

Craftsman Eager 1 problem (Continued.....)

uhm, guys i think i found the real problem. today i got it started and running. but i took off the oil cap cause i saw some smoke. but when i took it off, the exhaust was comming out of the oil...
Replies: 16
Views: 2,173
Posted By cmw0021

the only reason i didnt put a new one in is...

the only reason i didnt put a new one in is because i dont have one thats smaller. but my neighbor had the same problem. it ran fine only when warm. but since i played with it. it starts faster. but,...
Replies: 16
Views: 2,173
Posted By cmw0021

well, now i prime it 5 times pull it 5 times and...

well, now i prime it 5 times pull it 5 times and starts and runs. but 15 seconds later it slowly dies. it does this maybe 2 or 3 times. then after that it starts right up and continuosly runs. im...
Replies: 16
Views: 2,173
Posted By cmw0021

wooops... spoke too soon. it seems now like it...

wooops... spoke too soon. it seems now like it only runs when its warm. does that mean i should put a new plug in it, and some fresh gas? lol stumped again.
Replies: 16
Views: 2,173
Posted By cmw0021

yes but if you guys didnt help i wouldnt of been...

yes but if you guys didnt help i wouldnt of been looking at the carburetor. exhaust and all of that. thanks again and ill be back if any more problems occur.
Replies: 16
Views: 2,173
Posted By cmw0021

thanks for all of your help guys, it really...

thanks for all of your help guys, it really helped. but all i needed to do was take out the o ring where the spring is at the bottom of the bowl. vroom vroom right up and stayed running. my neighbor...
Replies: 16
Views: 2,173
Posted By cmw0021

today i took out that problem seal. no different....

today i took out that problem seal. no different. but one thing i noticed is that the gaskets for the carb are beat up and torn. dont know if that is the problem because it could be sucking air. but...
Replies: 16
Views: 2,173
Posted By cmw0021

yes i will get a carb rebuild kit, but i just...

yes i will get a carb rebuild kit, but i just want to know what the problem is. im going to take the carb off today but it looks spotless in it. someone said it could be sucking air where it meets...
Replies: 16
Views: 2,173
Posted By cmw0021

yes, the float needle in the back of it is very...

yes, the float needle in the back of it is very flimsy, not sure if it is supposed to be like that.
Replies: 16
Views: 2,173
Posted By cmw0021

Same starting problem with craftsman eager 1

cheese, i took off the bowl, cleaned it and put it back in. still no go. and you said there were holes, there were none or i was looking at the wrong thing, here is what my carb looks like
...
Replies: 8
Views: 31,936
Posted By cmw0021

lol well snowman it is a neighbors lawnmower :D

lol well snowman it is a neighbors lawnmower :D
Replies: 8
Views: 31,936
Posted By cmw0021

it hasnt been sitting, but it is about 12 years...

it hasnt been sitting, but it is about 12 years old but well taken care of.....so all i have to do is take the carb off the motor and clean the bowl. but soaking it, could i do that and would that...
Replies: 8
Views: 31,936
Posted By cmw0021

Craftsman Eager 1 Starting Problem

i have a craftsman eager 1 and it just will not start. after about 30 pulls it starts and then just slowly dies and wont start back up. ive heard about the carb needs to be cleaned and the bowl. but...
Replies: 8
Views: 17,354
Posted By cmw0021

also, which screw is the air and fuel, one is...

also, which screw is the air and fuel, one is short and one is a little longer, the shorter one is closer to the air filter, and the longer one is near the cylinder. Also, there is a screw all the...
Showing results 1 to 25 of 30
 


 
Forum Jump