Search: Posts Made By: bernieb
Showing results 1 to 23 of 23
Search took 0.04 seconds.
12-15-07, 02:16 PM
Replies: 1
Views: 520
Posted By bernieb

starting seeds

http://www.associatedcontent.com/article/24824/how_to_plant_and_grow_apple_trees_from.html
11-30-07, 05:11 AM
Replies: 1
Views: 2,349
Posted By bernieb

Aquaponics

I am in the process of pursuing the subject of "aquaponics" I have the concrete pond in place 12 feet wide 6 feet deep (a circle) creek rock faced, and the near-by 3 foot high concrete walled with...
Replies: 7
Views: 984
Posted By bernieb

Also

Lets not jump to conclusions here. Is your freezer working fine? The heat you feel may be normal. you can always wire your fan directly to an outside source to verify good or bad. Your fan may only...
Replies: 7
Views: 984
Posted By bernieb

refridgerator.

Before you get involved.....take model number to Sears and find out what a replacement condencer fan motor cost, if in your budget order it. Replacement is easier by laying refridg. on side . That...
11-29-07, 06:47 AM
Replies: 3
Views: 8,478
Posted By bernieb

building a homemade skimmer

This reply is a little late, but here we go ..... I made mine out of concrete ,and it was very easy I might say . Go to a marine dealership where they sell boats and buy a round floor access plate...
Replies: 4
Views: 2,560
Posted By bernieb

Lot to consider

Depending what type of person you are, and if you want the biggest bang out of the buck,or at least getting the most out of your investment and have fun in the process. After owning a i/o and now...
Replies: 5
Views: 1,664
Posted By bernieb

Try this.

Get some tapered building wood shims for the separation metal to metal.
Replies: 3
Views: 1,072
Posted By bernieb

antenna

You can buy the swing base locking handle at any marine store for around 7 bucks .
Replies: 1
Views: 1,110
Posted By bernieb

the outboard

Since I don't know what brand,what year ,what hp ,I can only assume. My knowledge is with the modern efi high hp models. It sounds like it may be in your carb. but for starters,have you de-carbonized...
Replies: 4
Views: 1,352
Posted By bernieb

RV check-out.

I would concentrate on good battery cables, a good engine ground connection, good battery clamps. You need a helper to listen for the solenoid click that mounts on the starter when trying to start....
Replies: 5
Views: 22,913
Posted By bernieb

high revs

I may have found my problem with the high revs only. I didn't want to clutter your brain with all thats been going on so i'll start all over again . While cutting grass I started putting out huge...
Replies: 5
Views: 22,913
Posted By bernieb

high revs

The engine starts right up ,but very high rpms,no spuddering,no missing,and moving any linkage on carb does nothing. Now the choke will stall it ,but thats it. What causes more gas to flow in carb?...
Replies: 5
Views: 22,913
Posted By bernieb

High reving briggs and stratton.

This riding lawnmower 16.5hp model 313777 type 0163-e5 has a high rpm problem and the motor is a briggs and stratton. I believe it has a Walbro carburetor and not sure how it works.On the very bottom...
Replies: 10
Views: 7,683
Posted By bernieb

hello again

Although this is an excellent forum,i advise you to visit the evinrude forum on iboats .com and present your problem .I done some research on your engine and it has been a good one for evinrude so if...
Replies: 10
Views: 7,683
Posted By bernieb

The engine

Are you getting a horn going off after a short run,and are you premixing the fuel. or do you have a on-board oil tank? I'm confused on year and horsepower rating you have. By all means don't run on...
Replies: 10
Views: 7,683
Posted By bernieb

sorry

I missed the water coming out the little hole. It may not be the missed water connection. You may have a so called pop-it valve on your engine it is designed to be closed at idle and opens when...
Replies: 10
Views: 7,683
Posted By bernieb

The line up.

When changing the impeller it's very tricky about lining up the cooling water connection points.Once the lower unit has been dropped down take a mirror using sunlight to be able to see where you need...
Replies: 7
Views: 1,847
Posted By bernieb

Boat repair

Not knowing what your floor looks like ,but i'd consider using the thick heavy matting for fiberglass cloth ,not the thin stuff at walmart and lay it to your floor ,maybe even running the cloth up...
Replies: 3
Views: 9,473
Posted By bernieb

Starter maybe

I had a 350 mercruiser that had similar problems and it was the slave solenoid but you may put a socket and breaker bar on the front crank nut pully and make sure the engine is not locked up and will...
Replies: 2
Views: 609
Posted By bernieb

88' chev. 2.5 fi (electric problem) I think

This engine has tbi with single injector and the engine runs as long as someone is spraying gas down tbi with a plastic bottle with a hole in it. There is gas pressure right at tbi and sometimes the...
Replies: 3
Views: 1,009
Posted By bernieb

Thanks Cabot

The guy picked up the wrong compressor and the wrong dryer.His car was a 94 instead of a 97 (thanks to vin numbers).Now have the right ones .The history (why it was taken out) was because the clutch...
Replies: 3
Views: 1,009
Posted By bernieb

installing a new a/c compressor

The vehicle is a 97 Crysler town and country and the replacement compressor has a sticker that says pac oil for (134-a) refrigerant and the label on hood says (134-a) .What i want to know do i need...
Replies: 3
Views: 1,685
Posted By bernieb

bernieb

On the "downstairs toilet" make sure the little holes in the china,just under the seat are clear ,it's where water comes out to assist the flushing,a nail will do it.We're all guilty of it but too...
Showing results 1 to 23 of 23


 
Forum Jump