Search: Posts Made By: 84EdH
Showing results 1 to 25 of 200
Search took 0.02 seconds.
02-25-20, 08:15 PM
Replies: 5
Views: 273
Posted By 84EdH

Ok got it. Thanks for all the help!

Ok got it. Thanks for all the help!
02-24-20, 08:25 PM
Replies: 5
Views: 273
Posted By 84EdH

Ok, to see if i understand : if i shut off...

Ok, to see if i understand :
if i shut off all the light switches at, and, after the open neutral, leaving receptacles wired as usual then the neutral voltage should be gone ?
02-24-20, 07:27 PM
Replies: 5
Views: 273
Posted By 84EdH

1/2 of a circuit out with lost neutral

Residential home has 1/2 of a circuit malfunctioning( half of the outlets and lights work fine, the other half not).
There is power to all points and in fact, the voltage detector beeps on both...
Replies: 7
Views: 430
Posted By 84EdH

Is 18 guage thermostat wire heavy enough to wire...

Is 18 guage thermostat wire heavy enough to wire the zone valves to the taco valve controls? (obviously the low voltage circuits)

also, thanks for the info. George, I have looked over the diagram...
Replies: 7
Views: 430
Posted By 84EdH

Thankyou for the help ! I will follow your guide...

Thankyou for the help ! I will follow your guide and wire it up tomorrow.

I appreciate you sharing your knowledge !
Replies: 7
Views: 430
Posted By 84EdH

understood. Now, the circulator is hooked up to...

understood. Now, the circulator is hooked up to the hydrostat. Whenever the thermostat calls for heat, circulator comes on. I thought that when i wire in the zone valves, the output of the taco...
Replies: 7
Views: 430
Posted By 84EdH

Wiring taco zone control to 3 V8043 zone valve

Taco ZVC404 EXP 4 ZONE VALVE CONTROL used to control 3 honeywell V8043 zone valves (no DHW and no priority.

I am trying to wire up this system and I am confused. I only use 1 circulator which is...
Replies: 6
Views: 300
Posted By 84EdH

ok, I will try reversing it. thanks !

ok, I will try reversing it.

thanks !
Replies: 6
Views: 300
Posted By 84EdH

attempt to rotate pic to proper orientation

attempt to rotate pic to proper orientation
Replies: 6
Views: 300
Posted By 84EdH

The valve is already soldered in place. I took...

The valve is already soldered in place. I took the motor off, and switched the cover over the valve area around to put the electrical contacts on top. However, when I put the valve in auto...
Replies: 6
Views: 300
Posted By 84EdH

Honewell V8043F1036F1036 zone valve

One of my 3 zone return lines to my oil boiler comes from below. In order to install the zone valve in the correct flow direction, it puts the wire connections on the bottom. Anyway to get these...
Replies: 0
Views: 253
Posted By 84EdH

New Boiler Buderus G115ws Question

My new boiler Buderus g115ws/4 with Riello burner is up and running seemingly fine.
The installer told me after the boiler was started that he did not have guages to fit the Riello burner. It seems...
Replies: 6
Views: 363
Posted By 84EdH

the photo is turned, the air valve is actually up

the photo is turned, the air valve is actually up
Replies: 6
Views: 363
Posted By 84EdH

photo of fill location above expansion tank

I have attached a photo of the fill location on my system. the city water attaches to the open fitting.

I am just trying to test my new piping including sweat joints, pipe threads, circulator...
Replies: 6
Views: 363
Posted By 84EdH

can I just allow the city water to fill the...

can I just allow the city water to fill the system through the pressure reducer on top of the expansion tank, and test the system like that? there is no heat involved and the overall pressure will...
Replies: 6
Views: 363
Posted By 84EdH

Leak test boiler system

Can I open the pressure release valve and plug it, to run full pressure tap water into system to see if all the sweat joints and piping is tight ?

also, once the system is full, can I power the...
Replies: 2
Views: 307
Posted By 84EdH

yes thats the plan for Monday. Thanks for...

yes thats the plan for Monday.

Thanks for the get back !
Replies: 2
Views: 307
Posted By 84EdH

New Buderus G115-4 WS wrong burner package?

I just got a new Buderus G115-4 oil fired boiler and during setup, I was reading the Burner install booklet. This boiler package is for a Riello 40 F5. The unit net output with a chimney is...
Replies: 2
Views: 328
Posted By 84EdH

thanks Spott, its unfortunate because you cant...

thanks Spott, its unfortunate because you cant see the boiler temp without getting your head over top of the unit. Also, it kind of is in the way of seeing the pressure guage.'
Replies: 2
Views: 328
Posted By 84EdH

Fuel Smart 3250 hydrostat plus mounting issue

Hello again, i have a new Buderus g115 ws and trying to mount the hydrostat to the boiler.

There is a hydrolevel electro well immersion well sticking out of the top of the boiler. The hydrostat...
Replies: 3
Views: 243
Posted By 84EdH

Hydrolevel Hydrostat 3250 control. I am...

Hydrolevel Hydrostat 3250 control. I am replacing my boiler with Buderus g115-4, this is the controller that comes with it. I should add a local contractor will do the install with my help moving...
Replies: 3
Views: 243
Posted By 84EdH

Taco 3 Zone Valve Control Module With Priority

Taco ZVC403-4 3 zone control module

will this unit control 3 separate zone for baseboard heat, and a separate indirect water heater, or would the indirect hot water heater command its own zone ?
...
Replies: 13
Views: 487
Posted By 84EdH

I have 160ft baseboard. I did the slant fin heat...

I have 160ft baseboard. I did the slant fin heat calc. for the numbers I came up with.
when I went back over the calculations, I made some adjustments to the basement heat loss, because I had...
Replies: 13
Views: 487
Posted By 84EdH

thanks for the input about the output !

thanks for the input about the output !
Replies: 13
Views: 487
Posted By 84EdH

so I went over my calculations mostly accounting...

so I went over my calculations mostly accounting for the basement walls are mostly below grade. I changed the garage indoor temp to 38 degrees, which keeps it above freezing (my goal).

depending...
Showing results 1 to 25 of 200
 


 
Forum Jump