Search: Posts Made By: MAS
Showing results 1 to 25 of 26
Search took 0.01 seconds.
06-24-07, 09:14 AM
Replies: 5
Views: 9,533
Posted By MAS

Best siding nailer for Hardi??

What's the best siding nailer to apply ring shank nails for hardiplank/certainteed fiber cement board lap siding?

Thanks,

Mas
06-24-07, 09:05 AM
Replies: 2
Views: 1,288
Posted By MAS

Flashing tape...over or under?

Hi,

When setting new vinyl windows with fins & using flashing tape, does the flashing tape go over or under the building paper on the sides? I know that the bottom goes over the building paper...
06-11-07, 09:05 PM
Replies: 1
Views: 2,107
Posted By MAS

HardiPlank vs Certainteed or other??

Which is the better siding product...and why?

I live in wet Washington State & looking for a quality fiber cement siding. I'm planning on about 4" exposure on the planks. I'm leaning toward...
Replies: 5
Views: 1,223
Posted By MAS

Thumbs down Water is coming through a few hairline cracks in...

Water is coming through a few hairline cracks in the slab...and around the edges. Check out the picture link I just added:
http://i129.photobucket.com/albums/p219/mas421/ParkingSlab.jpg

Last...
Replies: 5
Views: 1,223
Posted By MAS

Sealing elevated parking slab for waterproofing

Hi,

I'm wanting to apply a waterproof sealant to an elevated parking slab to allow for the construction of a room below. Currently when it rains, water will seep throught he slab & drip down...
Replies: 1
Views: 1,693
Posted By MAS

Chime mode with siren? Vista 20P

Is it possible to set certain zones to chime while arming others for siren on the same partition?

Thanks,

Mas
Replies: 6
Views: 4,524
Posted By MAS

Another False alarm on ademco motion/Vista 20P

OK...I thought all was fixed. I replaced the motion about a month ago...then I had another false last night. It got me right up!!


I do not have any pets. The heat was not on. Nothing fell...
Replies: 6
Views: 4,524
Posted By MAS

False Alarm w/Ademco PIR on Vista 20p

Got my neighbor's attention with a false alarm today. An interior motion was set off with no sign of entry and doors still locked and untripped...no pets either! I've had the system live for over a...
Replies: 4
Views: 1,257
Posted By MAS

Great, Thanks for the reply. I cannot wait...

Great,

Thanks for the reply. I cannot wait to try it out.

Mas
Replies: 4
Views: 1,257
Posted By MAS

RF Range for Ademco 5881

What's the transmission range for these guys...and can they be placed inside the control box???

I've got 4 walls (sheetrock & wood studs) that the signal needs to travel through.

I'm waiting...
Replies: 2
Views: 1,255
Posted By MAS

Thanks, this helps a lot! Mas

Thanks, this helps a lot!

Mas
Replies: 2
Views: 1,255
Posted By MAS

Ademco 5816 door/window transmitter

Hi,

I am not familiar with these transmitters at all, so I've a couple of questions:

Can I wire three doors (contacts wired in series) with one 5816?

These are two zone...right? ...so can I...
Replies: 7
Views: 992
Posted By MAS

So, the RF receiver has the zone screw terminals...

So, the RF receiver has the zone screw terminals built-in....so I do not need any additional zone expanders??? Right?

Mas
Replies: 7
Views: 992
Posted By MAS

I've only have eight zones...but I do not have...

I've only have eight zones...but I do not have anymore screw terminals & I have just one sensor in each zone. My system can handle up to 48 (I believe)...but it has not been expanded. I'm I missing...
Replies: 7
Views: 992
Posted By MAS

I've got the Vista 20P. Does this change any...

I've got the Vista 20P.

Does this change any of the recommedations?

Also, what type of zone expander will I need?

Thank you,

Mas
Replies: 7
Views: 992
Posted By MAS

Shopping list for adding wireless to vista 20

Hi,

I want to add two wireless door sensors to my existing vista 20 panel. Currently, my entire system is hard wired, but I want to add wireless to my detatched garage's two entry doors & maybe a...
Replies: 2
Views: 3,258
Posted By MAS

Yup, That did it. Everything works perfectly...

Yup, That did it. Everything works perfectly now!


Thanks RonFl !!!!!

MAS
Replies: 2
Views: 3,258
Posted By MAS

Vista 20P Motion Detector programming issues

I've recently added a new keypad to my system in the upstairs. I've gotten the new keypad addressed & working just fine. Now what I'm wanting to do use the stay & nightstay mode correctly.

I...
Replies: 1
Views: 1,028
Posted By MAS

Vinyl Slider Door & Flush Mounted Door Sensor

Where/how is the best way to mount a Ademco magnetic flush mounted sensor on a vinyl sliding door?

Should I mount it on the top or the side of the slider?

Also, what is the maximum gap for...
Replies: 8
Views: 3,462
Posted By MAS

Still having problems...! I've set all three...

Still having problems...!

I've set all three of my motions to 20 in *56...just trying to get something. I've tried arming in stay & away...each time opening/closing the entry door. I did get the...
Replies: 8
Views: 3,462
Posted By MAS

RE: Vista 20P: No Alarm with Motion Detector

I'm doing "live" tests in away mode...but staying indoors after arming then walking around until the sensors blink red. The sensors blink but the alarm does not sound. During "test" mode, the...
Replies: 8
Views: 3,462
Posted By MAS

Vista 20P: No Alarm with Motion Detector

Anyone, Please Help!

Firstly, Thank you to those who have responded to my earlier questions!

OK, I'm still new to alarm installation, but things are getting closer.

I've finally gotten...
Replies: 2
Views: 4,352
Posted By MAS

programming vista 20P from scratch

Please help...again,

OK, I've gotten my 6150 keypad to respond by addressing it to 16. Then I've entered programming mode using 4112 800 which then displays 20. What exactly do I do now? I...
Showing results 1 to 25 of 26
 


 
Forum Jump