Search: Posts Made By: Okie294life
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 1
Views: 117
Posted By Okie294life

Shot in the dark...

To adjust the unloader valve you should be able to just back off the nut on the back of the valve some to adjust it, a lot of them have a little black handle where it can be done manually. It sounds...
Replies: 1
Views: 161
Posted By Okie294life

Toro Super Recycler Transmission Issue

I have a SR4 20057, model number. The self propel works somewhat, but when you go to pull it in reverse the wheels hang up. This happens randomly, Iíve taken the gear assembly apart and centerlined...
04-04-20, 04:01 PM
Replies: 2
Views: 435
Posted By Okie294life

Mini blind fix?

I have a door blind that broke the little vinyl cord which pulls them up and down, not the pull cord...smaller diameter. Anyone know what gauge this is and how to get ahold of a few feet of this cord?
Replies: 7
Views: 286
Posted By Okie294life

Tried all that.

Took everything apart (carefully) cleaned it and put it back together with some kroil. It still grabs some but better. Maybe this thing is missing some parts or something? May need to centerline this...
Replies: 7
Views: 286
Posted By Okie294life

Toro super recycler issue.

I have a toro super recycler 20057, with the b&s engine. When I go do disengage the drive and back up, there are problems. To get the transmission to unlock you punch the drive handle real hard...
Replies: 9
Views: 450
Posted By Okie294life

Get it leak tested

Check the torque on your head bolts first against OEM spec, normally they should not be any higher than 90 in pounds. Also make sure there is no grease or any contamination on the bolt threads. If...
Replies: 10
Views: 359
Posted By Okie294life

Check the air filter and choke flap..

I had an echo blower had close to the same issues. I put an aftermarket air filter in it and it interfered with the choke lever. Also there was a little screw on the choke lever that had slipped...
Replies: 9
Views: 450
Posted By Okie294life

Donít need a ring compressor.

Make sure that the rings are lined up to the pins (they arenít upside down) compress one, get it started on one side and hold slight tension on it, then using your fingernails press the ring in all...
Replies: 1
Views: 267
Posted By Okie294life

Easiest way to set valves on Briggs self propelled mower?

Iím not an expert at this but I read on a forum somewhere to lift one valve and clearance the other repeat this twice at .004. I tried it and the mower starts good, but the exhaust still smells like...
Replies: 2
Views: 180
Posted By Okie294life

What engine is on this?

i just got a toro mower super recycler sp4 2005-2006, itís got a Briggs on it but Iím trying to figure out what model and hp it is. Itís OHV, and it has an oil filter. Iíve got no idea at this point.
Replies: 5
Views: 740
Posted By Okie294life

Check out your gaskets

Look at your gaskets to ensure you arenít blocking the hole that leads to the impulse. If your intake gasket got put on backwards or not at all this pressure wonít get to the carb, itís what causes...
Replies: 5
Views: 344
Posted By Okie294life

Options

I hope chasing the threads gets them back, if it doesnít donít do the heli coil. They suck. Youíd be better off finding a used cylinder head off eBay, or Iíve also heard of guys getting a larger...
10-13-19, 12:35 PM
Replies: 16
Views: 5,234
Posted By Okie294life

Do it carefully.

Most states/municipalities will let you hand dig around lines, and most utilities are at least 12Ē deep. My take would be to hand dig around the stump carefully until 2-3 inches below grade and top...
Showing results 1 to 13 of 13


 
Forum Jump