Search: Posts Made By: kyle johnson
Showing results 1 to 25 of 144
Search took 0.02 seconds.
Replies: 8
Views: 617
Posted By kyle johnson

DeskJet 840C Printer keeps blinking

Product Name: DeskJet840C
Operating System: Microsoft Windows XP
It worked fine last week when I had Charter (Spectrum). Now I have AT&T. Everytime I try to print on my DeskJet840C it just blinks...
Replies: 4
Views: 4,338
Posted By kyle johnson

transmission problems on Murray Riding lawnmower

It's a 14 hp ... 42" cutting deck
It just quit going ....5th gear....1st gear....it doesn't matter
Do I need to put transmission fluid in it??
Maybe tighten up something?

Thanks
Replies: 12
Views: 21,436
Posted By kyle johnson

Hey Furd... You seem like you are a smart...

Hey Furd... You seem like you are a smart aleck.....No... I know you are a smart ass... I don't think!!
Replies: 12
Views: 21,436
Posted By kyle johnson

Yes ... my charger is an older model with a...

Yes ... my charger is an older model with a needle gauge on the front
Replies: 12
Views: 21,436
Posted By kyle johnson

I think they are deep cycle. The two amp slow...

I think they are deep cycle.
The two amp slow charge will give it a better longer charge.
I could put it on a quicker charge....6 amp.
Replies: 12
Views: 21,436
Posted By kyle johnson

>Boat-Trolling Motor< Battery Re-Charge: How long??

I've got the battery on slow charge for 4 hrs....so for. How long do I "slow charge the battery for the trolling motor???
How long do I slow charge the regular motor that starts the boat??
I've...
Replies: 7
Views: 902
Posted By kyle johnson

Normally there's a cap covering arm to axle...

Normally there's a cap covering arm to axle attachment. Remove the cap and there should be a tightening bolt, securing arm to the axle. If that nut is gone, here's your answer.
If the splines are...
Replies: 7
Views: 902
Posted By kyle johnson

2000 ZR2 Blazer...Driver Wiper is not in sync...must be loose. How?

How would I go about fixing my loose wiper on the drivers side? I've raised it up and there is no screw to adjust. Should I take out the grill below (beside) the wiper? Should I just carry it to a...
Replies: 4
Views: 4,185
Posted By kyle johnson

so.....it is the blade. I didn't know what to do...

so.....it is the blade. I didn't know what to do or if it was the fence
08-06-12, 08:28 PM
Replies: 1
Views: 1,422
Posted By kyle johnson

I don't have a termite contract....

I guess I should be worried, but so for, so good. Do I have to use Terminex or some of these other companies? Or can I go to Lowe's or some hardware store and buy some type of chemical and do it...
Replies: 4
Views: 4,185
Posted By kyle johnson

Tradesman 10" compound miter saw "not cutting straight"

Not cutting straight on a 90* cut. It cuts like it about 2* off. Do I need a new blade?? Is the saw bad?? Is there some type of adjustment I can do??
Thx for your help.
Replies: 1
Views: 1,992
Posted By kyle johnson

Garbage disposal will hum but is not jammed.

It will turn freely back and forth. Do I need a new one??
Thx for your help.
Replies: 8
Views: 1,294
Posted By kyle johnson

My laptop is a Vista and my desktop is an...

My laptop is a Vista and my desktop is an XP...Hope that helps.
Replies: 8
Views: 1,294
Posted By kyle johnson

Several Computer Questions:

Is there a FREE virus protection out there to download? Such as AVG; Malware bytes; SuperAnti-spyware, Spyware Doctor,etc.
Is there one that is free and real good?? Or should I just go to Walmart...
Replies: 1
Views: 823
Posted By kyle johnson

New spark plug, new inline fuel filter.......

oil is where it should be on the dipstick...gas is almost full... it will crank then die (quit) after a couple of seconds...then when I try to start it again... all it does is just spin, but doesn't...
Replies: 3
Views: 1,361
Posted By kyle johnson

Smile thx... I will try to work on this tomorrow...

thx... I will try to work on this tomorrow (Thurs.) and I will work on these in the order that you mentioned. Thx.
Replies: 3
Views: 1,361
Posted By kyle johnson

Murray B&S Riding Lawnmower not firing on up....

It will turn over and actually fire (crank) and run for about 3 sec. and then die (shut off)...then when I try to start it again... all it does is just spin, but doesn't fire. The blade is...
Forum: Water Heaters
09-18-09, 03:25 PM
Replies: 10
Views: 975
Posted By kyle johnson

Thank you We'll get it done next week,...

Thank you
We'll get it done next week, hopefully.

Thanks for ya'lls help

Kyle
Forum: Water Heaters
09-18-09, 09:47 AM
Replies: 10
Views: 975
Posted By kyle johnson

What do you mean you are going to move this...

What do you mean you are going to move this thread to the proper forum? It is in the proper forum.

And #2. You lost your bet. There IS NOT an expansion tank!
Forum: Water Heaters
09-17-09, 02:14 PM
Replies: 10
Views: 975
Posted By kyle johnson

Thank you. I'll try this in a few days from...

Thank you.
I'll try this in a few days from now. Maybe this will work. I just didn't know what to do next. I was lost.

Kyle :o
Forum: Water Heaters
09-17-09, 08:28 AM
Replies: 10
Views: 975
Posted By kyle johnson

Nobody knows what to do - Help please...

I have an Electric Hot Water Heater (40 gal) that is about 3 yrs. old. It started leaking from the pop off valve about 4 mths. ago. Well last month we put a new pop off valve on.. it leaked. So...
Replies: 5
Views: 42,309
Posted By kyle johnson

I've got it on 2 amp and 12 volt charge. 6 holes...

I've got it on 2 amp and 12 volt charge. 6 holes in the battery; so therefore it should be on 12 volt and 2 amp so that it'll be on a slow trickle charge for 48 hrs. I'll charge it one more...
Showing results 1 to 25 of 144
 


 
Forum Jump