Search: Posts Made By: rskram
Showing results 1 to 25 of 31
Search took 0.01 seconds.
Replies: 2
Views: 347
Posted By rskram

I thought so but wasn't positive. Thanks

I thought so but wasn't positive. Thanks
Replies: 2
Views: 347
Posted By rskram

Piston Rod Cap Question

Hello all. Just a quick question. I have a small engine that I took apart and noticed a tab about an inch long on the piston rod cap that connects the piston arm to the crankshaft. What is that for?...
Replies: 8
Views: 802
Posted By rskram

Valve timing

I lined up the two marks on the sprocket while the piston was at top dead center
Replies: 8
Views: 802
Posted By rskram

Valve timing

I lined up the two marks on the sprocket while the piston was at top dead center
Replies: 8
Views: 802
Posted By rskram

Flywheel

It turns a little and then it locks like you said. But it turns really really hard. I haven't loosened the bolts yet to see if that helps any.
Replies: 8
Views: 802
Posted By rskram

Found Parts

I found the cylinder assembly for the engine. I put it together and now the flywheel won't spin to turn the crank. What the heck is going on. I oiled up the piston, rings , and block. What could the...
Replies: 8
Views: 802
Posted By rskram

Thanks cheese for all your help.

Thanks cheese for all your help.
Replies: 8
Views: 802
Posted By rskram

Old Engine Parts Locator

Hello all, I have a Honda GC160 5hp engine serial number GCAHA 1915491 that came off an Excell 2500 powerwasher , engine family 3HNXS.187AK with a 7/8 short tapered shaft that I need parts for. The...
Replies: 1
Views: 633
Posted By rskram

Shaft and pump on a power washer.

I have a Excell 2500 power washer and the Honda
GC 160 5hp engine head cracked. I was going to replace the engine with a Predator engine from HF but the shaft is 3/4" in diameter and 2.43" long and...
Replies: 14
Views: 1,045
Posted By rskram

I cleaned that carb twice, really good. All...

I cleaned that carb twice, really good. All inlets had carb cleaner coming out. So I'll do what you said tomorrow and see what happens. Cheese, thanks for all your help. I'm determined to get this...
Replies: 10
Views: 1,436
Posted By rskram

Thanks for the help ukrbyk and alan73. I never...

Thanks for the help ukrbyk and alan73. I never took the compressor off the vehicle. So by vacuuming the system it took the oil out of the compressor? Do you think I should get a new compressor to be...
Replies: 14
Views: 1,045
Posted By rskram

All is fine with the timing of the piston. The...

All is fine with the timing of the piston. The valves and piston are acting like you said. I'm thinking it's a carb flooding problem because it sounds like alot of gas in the intake housing. I used...
Replies: 14
Views: 1,045
Posted By rskram

Valve timing

Also, how do you check the valve timing on this engine? Thanks again
Replies: 14
Views: 1,045
Posted By rskram

Thank you cheese. I'm not junking it. I'm just...

Thank you cheese. I'm not junking it. I'm just angry that I can't get this thing working. I do have mechanicable ability so that's why I'm still trying this. I took the carb off again and cleaned it...
Replies: 10
Views: 1,436
Posted By rskram

I did not fill the compressor with oil but I did...

I did not fill the compressor with oil but I did add oil to the Freon when charging. When you say shorten the terminals on the pressure switch what do you mean?
Replies: 14
Views: 1,045
Posted By rskram

Junk it?

Thanks for the info cheese. If it's anything other than the engine flooding should I just junk the engine? Not sure if I've got the time or tools to do that job.
Replies: 10
Views: 1,436
Posted By rskram

Thanks for the reply. I put in one 12oz can of...

Thanks for the reply. I put in one 12oz can of r134 a. I put it in with the gauge that came with the can because I didn't have the adapter to put it in with the ac gauges. The can gauge was reading...
Replies: 14
Views: 1,045
Posted By rskram

On/off switch is on. The oil is good. Is it...

On/off switch is on. The oil is good. Is it possible it could be the fuel pump? I sprayed some gas in the spark plug port to see if it started but it did not. I'm stumped. There's got to be someone...
Replies: 10
Views: 1,436
Posted By rskram

Ac Compressor Question.

I have a 2011 GMC Acadia in which I replaced the discharge line due to a large hole. After replacing the line I vacuumed the lines. I then filled up with R134A and the air did not get cold. The...
Replies: 14
Views: 1,045
Posted By rskram

Almost on fire.

I checked the oil and it is full. I pulled off the air filter and pulled the chord and a flame came out of the air filter housing. Never had that happen . Is it possible that I put the carb jet in...
Replies: 14
Views: 1,045
Posted By rskram

Excell 2500 powerwasher won't start. What should I check?

Hello all , I have an Excell 2500 powerwasher with a Honda 5hp engine that won't start. I was using the pw and than it turned off. I thought I ran out of gas but that's not the case. There was fuel...
Replies: 3
Views: 1,615
Posted By rskram

Thank you for the reply. If I'm understanding...

Thank you for the reply. If I'm understanding the evap system correctly isn't the canister vent valve solenoid always open and only closes when the pcm requires a test on the evap system? And the...
Replies: 3
Views: 1,615
Posted By rskram

P0455 and p0449 codes

Hey guys, I have a 2007 Chevy Colorado with a p0449 and a p0455 code. I've changed the purge valve solenoid, the gas cap, and the canister vent valve. I'm still getting the codes. I've done a...
12-29-17, 07:04 AM
Replies: 3
Views: 691
Posted By rskram

Furnace Blower Motor Constantly On

Hello guys, I have a RUUD Silhouette II furnace that the blower motor keeps running after the call for heat has been satisfied. I have replaced the filter and the upper limit sensor. The flame...
Replies: 5
Views: 597
Posted By rskram

Thanks aka Pedro. I'll give it a checking out.

Thanks aka Pedro. I'll give it a checking out.
Showing results 1 to 25 of 31
 


 
Forum Jump