Search: Posts Made By: bmcguane
Showing results 1 to 25 of 86
Search took 0.02 seconds.
Replies: 2
Views: 192
Posted By bmcguane

Thank you, it's much appreciated,!

Thank you, it's much appreciated,!
Replies: 2
Views: 192
Posted By bmcguane

Can I paint Styrofoam ?

I am going to be installing foam board insulation on the exterior of my concrete foundation. Eventually I will be re-siding and it will be covered with vinyl. In the meantime I was hoping to paint it...
Replies: 3
Views: 415
Posted By bmcguane

Re-using stones with mortar

I had a small stone and mortar wall fall apart from years of neglect and I would like to replace it. I have a lot of stone with mortar still attached and I was wondering if the mortar could be...
01-29-15, 02:15 AM
Replies: 1
Views: 600
Posted By bmcguane

Type of venting required for oil furnace

Is it acceptable to use galvanized pipe and fittings to vent an oil fired, forced air furnace. the existing galvanized pipe is old and deteriorating. The furnace is old and probably going to be...
Replies: 1
Views: 466
Posted By bmcguane

chrysler Sebring heat control problem

I have a 2004 Chrysler Sebring that has issues with the heating/cooling controls. It is on full heat and I cannot get the controls to change vents, it blows in my face but cannot get it to defrost or...
Replies: 14
Views: 978
Posted By bmcguane

Well what I did was separate the inner boot of...

Well what I did was separate the inner boot of the cv axle. I was unable to get the old axle out, rented a slide hammer and axle removal tool. I just could not get any leverage with the car on jack...
Replies: 14
Views: 978
Posted By bmcguane

The ball joint was shot. Had a lot of play in it...

The ball joint was shot. Had a lot of play in it and got a good "thunk" every time we started to move
Replies: 14
Views: 978
Posted By bmcguane

I'm afraid Saturday will be my next opportunity...

I'm afraid Saturday will be my next opportunity to work on it. I ordered/received a new CV axle. I will try again when it gets above freezing.
Replies: 14
Views: 978
Posted By bmcguane

Looking back at my post it looks like I did not...

Looking back at my post it looks like I did not give a very good description. I'll try again;
I had a hard time getting the existing control arm out and while twisting and pulling it felt like the...
Replies: 14
Views: 978
Posted By bmcguane

I wasn't working on the axle at all I just can't...

I wasn't working on the axle at all I just can't get the new control arm in. The wheel assembly doesn't seem to have much flexibility and I was wondering if I possibly pulled the axle out of where it...
Replies: 14
Views: 978
Posted By bmcguane

Axle problems 2000 Honda Oddyssey

I am trying to change the lower control arm on the drivers side of my Honda Minivan. I got the old one out but I am having trouble getting the new one in. Is it possible that I separated or loosened...
10-12-14, 04:40 AM
Replies: 1
Views: 685
Posted By bmcguane

exposed concrete foundation

I have a concrete foundation that is exposed to the northeastern weather. It is exposed anywhere from 1 foot to about 4 foot. I was considering digging down below the frost line and installing some...
Replies: 1
Views: 2,229
Posted By bmcguane

transmission problems

I have a 2003 Chevy Silverado with a 4L60E transmission. I was told by the mechanic that I need a new transmission. It shifts late at a high rpm. The fluid and filter have been changed. It was being...
04-27-14, 06:59 PM
Replies: 8
Views: 892
Posted By bmcguane

I bypassed the thermal fuse (for just a minute)...

I bypassed the thermal fuse (for just a minute) and it fired up. I will buy a replacement and all will be well. Thank you all for all the help.
04-27-14, 09:51 AM
Replies: 8
Views: 892
Posted By bmcguane

TGDS680EQ3,sorry I left a number out

TGDS680EQ3,sorry I left a number out
04-27-14, 09:22 AM
Replies: 8
Views: 892
Posted By bmcguane

It is a Whirlpool Estate Mod. TGDS80EQ3 Thanks...

It is a Whirlpool Estate Mod. TGDS80EQ3 Thanks for such a quick response
04-27-14, 08:42 AM
Replies: 8
Views: 892
Posted By bmcguane

Gas dryer not heating

I have a gas dryer that runs but does not heat. The igniter does not glow. I get a reading of 75 ohms on the igniter is this an indication on whether it is good or not? Thank you
Replies: 4
Views: 745
Posted By bmcguane

He never saw the damage or received any...

He never saw the damage or received any verification that a replacement was purchased. It was a deal to save a friendship, but it looks like it was a one sided friendship.
I have never seen CSI. I...
Replies: 4
Views: 745
Posted By bmcguane

Finding a computer

Hello, can anybody tell me if there is a way to find out if a particular computer is being used. A friend of mine had to replace a computer that he allegedly ruined and I believe it is still being...
10-30-13, 03:43 PM
Replies: 2
Views: 871
Posted By bmcguane

appraisal

We are going to refinance our home. There will be an exterior appraisal done. Anyone have any advice, do's or don'ts that might make a difference. We probably only have a week, thank you!
Replies: 2
Views: 973
Posted By bmcguane

Chevy pick up stalls after jump-start

I have a 2003 Chevy Silverado with a 4.8 v8 gas engine. After sitting for awhile I had to jump start it and now when I slow down for a traffic light or while turning it stalls. I thought I remember...
Replies: 3
Views: 14,133
Posted By bmcguane

The speed sensor we replaced was in the...

The speed sensor we replaced was in the transmition housing. I could not see any worm gear, but i wasn't looking either. Is that worm gear something that could be replaced without getting into...
Replies: 3
Views: 14,133
Posted By bmcguane

speedometer/odometer not working

I have a 1989 chevy K1500 with a 350 v8. the electric speedometer and odometer are not working I replaced the speed sensor and nothing!. I was going to take apart the dash and check connections an...
Replies: 8
Views: 4,929
Posted By bmcguane

Low Voltage

I have a Generator that is putting out between 50 and 80 volts on a 120 volt receptacle would this be the same fix?
05-16-11, 04:19 AM
Replies: 1
Views: 6,538
Posted By bmcguane

Wet couch

I have a couch with an upholstered seat and a wood back and armrest. It was left out in the rain ... for a day. Would there be any chance of saving it?
thanks
Showing results 1 to 25 of 86
 


 
Forum Jump