Search: Posts Made By: Steve749
Showing results 1 to 14 of 14
Search took 0.01 seconds.
02-02-14, 06:03 PM
Replies: 9
Views: 863
Posted By Steve749

I ended up getting a small bag of sheetrock 90 to...

I ended up getting a small bag of sheetrock 90 to do the job. I want to thank everyone for their help and explanations. It was greatly appreciated.

Steve
01-31-14, 02:56 PM
Replies: 9
Views: 863
Posted By Steve749

I checked out the Durabond website. Would DUREX...

I checked out the Durabond website. Would DUREX Ceiling Coat work?
01-31-14, 02:43 PM
Replies: 9
Views: 863
Posted By Steve749

How did it get its name of "brown coat"?

How did it get its name of "brown coat"?
01-31-14, 02:36 PM
Replies: 9
Views: 863
Posted By Steve749

The gray material has a texture of rough cement....

The gray material has a texture of rough cement. I don't known what it is called.
Looking up along the exhaust fan housing I can see wooden slats that appear to be imbedded in the material.
01-31-14, 01:44 PM
Replies: 9
Views: 863
Posted By Steve749

Plaster Bathroom Ceiling

Hi,

The plaster around the exhaust fan is cracking and separating from the gray material above it. I was able to remove about 2 sq ft of plaster with a putty knife. The plaster looks to be about...
06-26-13, 05:57 AM
Replies: 11
Views: 5,361
Posted By Steve749

I have finished up the job but wanted to get the...

I have finished up the job but wanted to get the photo up so you could see what I was talking about. The plywood fit nicely over the flange and was even with the bottom of the flange. The photo shows...
06-23-13, 05:05 PM
Replies: 11
Views: 5,361
Posted By Steve749

I keep getting an error 503 when trying to upload...

I keep getting an error 503 when trying to upload the photos. I will try to get it figured out and post then. Thanks.
Steve
06-20-13, 06:38 AM
Replies: 11
Views: 5,361
Posted By Steve749

I'm just replacing the plywood. There is a dirt...

I'm just replacing the plywood. There is a dirt basement. The 90 degree cast iron is tight against the bottom of the floor. It may be an ell or or a very very short piece of cast iron sticking...
06-19-13, 12:53 PM
Replies: 11
Views: 5,361
Posted By Steve749

I should have mentioned this is a first floor...

I should have mentioned this is a first floor bathroom. When you look in the pipe there is an immediate 90 degree bend. I guess I will cut a hole large enough to fit over the flange. Is there some...
06-19-13, 11:46 AM
Replies: 11
Views: 5,361
Posted By Steve749

Cast Iron Toilet Flange Question

Hello all,
I would like to remove the existing cast iron toilet flange to aid in installing the 3/4" plywood. The flange appears to be leaded to the cast iron pipe which I was not expecting....
02-10-13, 11:09 AM
Replies: 3
Views: 3,046
Posted By Steve749

I pulled the blower unit out far enough to see...

I pulled the blower unit out far enough to see inside the squirrel cage. The motor shaft has no side to side movement. The shaft does move very slightly in and out of the motor. The squirrel cage is...
02-09-13, 10:06 AM
Replies: 3
Views: 3,046
Posted By Steve749

Rheem Classic 90 Plus gas furnace. MDL: RGRA-06EMAES blower fan noise

Hi,

The blower fan is making noise and is getting worse. I've taken the front bottom cover off and wiggled the fan. There is alot of side to side movement. Are there any bearings on the fan...
Replies: 5
Views: 1,433
Posted By Steve749

Thanks

The block is not cracked, but the crank will need reground. The B&S engines seem priced right. Too bad they don't come in red.
Steve
Replies: 5
Views: 1,433
Posted By Steve749

Tecumseh on Horse Tiller

Hi,

I have an older Troy Bilt Horse garden tiller. It's a Tecumseh engine with a broken connecting rod. The number next to the spark plug is HMXL 70 132502 ser 6314D. I need help identifing it. Do...
Showing results 1 to 14 of 14


 
Forum Jump