Search: Posts Made By: diy_in_atl
Showing results 1 to 25 of 200
Search took 0.01 seconds.
Replies: 1
Views: 45
Posted By diy_in_atl

Indoor/outdoor chimney wet during rain

I have a chimney on the inside/outside of my house. It's not functional. It's been filled in and only is used for vents for my heater. I just noticed that it got a little wet during the recent...
Replies: 3
Views: 85
Posted By diy_in_atl

I've got the original remotes, they don't work...

I've got the original remotes, they don't work with LED lights, and the range is bad. That's why I'm asking if there a recommended after market module that works
Replies: 3
Views: 85
Posted By diy_in_atl

Advice on fan remote control

I am going to change my fan remotes out. They're the older Hampton Bay remotes. I need two of them. They need to be able to dim LED lights, and set the fan speed. Can someone recommend one? I'm...
Replies: 13
Views: 251
Posted By diy_in_atl

I agree. What's strange is the fans turn on...

I agree. What's strange is the fans turn on together. The lights don't.
Replies: 1
Views: 103
Posted By diy_in_atl

Fan buzzing after changing bulb

I climbed up and changed the bulb in my fan and also put the cowling back on plus tighten up the covers over the top lights. Now it makes a loud buzzing noise. I made a video:
Buzzing fan...
Replies: 13
Views: 251
Posted By diy_in_atl

I was able to take the canopy off, and I can see...

I was able to take the canopy off, and I can see the receiver and antenna under there. I exposed the antenna, as you suggested. No luck. I think I may have made it worse, because now the fan makes...
Replies: 13
Views: 251
Posted By diy_in_atl

Does the video help? Also, how do I stop...

Does the video help?
Also, how do I stop buzzing?
Replies: 13
Views: 251
Posted By diy_in_atl

Sorry, I meant the bulbs seem ok. Here's a video...

Sorry, I meant the bulbs seem ok. Here's a video I took off the behavior, I'm pressing the light button once on the remote each time.
Fan lights (https://youtu.be/zf-MwMqxdI8)
Replies: 13
Views: 251
Posted By diy_in_atl

Yes the bulbs seem to turn on fine. The one only...

Yes the bulbs seem to turn on fine. The one only seems to turn on if I stand directly below the fan light and point the remote up and at the fan.
Replies: 13
Views: 251
Posted By diy_in_atl

Ok. I'm just concerned that the something wrong...

Ok. I'm just concerned that the something wrong with the receiver since the fan party works but the light doesn't.
Replies: 13
Views: 251
Posted By diy_in_atl

Ok. How much wire? Is it possible that it's the...

Ok. How much wire? Is it possible that it's the receiver? Would it be better to replace it? The receiver is at least ten years old. I all because the fan turns on, it's the light that's in the...
Replies: 13
Views: 251
Posted By diy_in_atl

Hampton Bay fan remote only works directly below fan

I have two fans in my living room, separated by a chandelier. There's basically twelve feet between them. Both use remotes to control them and are on the same frequency as far as I can tell. Both...
Replies: 16
Views: 487
Posted By diy_in_atl

Yes, the part that goes over it is on there. ...

Yes, the part that goes over it is on there. That bottom thing is the shaft
Replies: 16
Views: 487
Posted By diy_in_atl

It's a Toro recycler with rear wheel drive. The...

It's a Toro recycler with rear wheel drive. The blade it had installed was a Toro atomic. I installed the same blade:
Toro atomic...
Replies: 16
Views: 487
Posted By diy_in_atl

The blade is indented so it only goes on one way...

The blade is indented so it only goes on one way as far as I can tell. I put it on exactly the way the other one was on, and I used a torque wrench as prescribed.
Replies: 16
Views: 487
Posted By diy_in_atl

It looked like the blade was keyed to only go on...

It looked like the blade was keyed to only go on one way. I have it on there tight, had to use a breaker bar to get it off, put it back on with a torque wrench and blue loctite
Replies: 16
Views: 487
Posted By diy_in_atl

Metal sound on mower after blade and belt change

I have a Toro mower I just changed the belt on, and while doing that I changed the blade. Used the same belt and blade models that took off. It cranks and runs but on start it kind of sounds like...
Replies: 9
Views: 346
Posted By diy_in_atl

Ok. I just hit the vent button on the unit and...

Ok. I just hit the vent button on the unit and it feels like it does spin. Is there some way to check to see what the actual RPM is supposed to be? What it looks like it's happening is that the...
Replies: 9
Views: 346
Posted By diy_in_atl

Is there a way to see what the pat # is for the...

Is there a way to see what the pat # is for the capacitor? I see this DE59-50002A capacitor but is it that part?
Replies: 9
Views: 346
Posted By diy_in_atl

Awesome thank you. I have another question....how...

Awesome thank you. I have another question....how do I take this thing off? I removed the two above-mount screws and it swung down, and I can see something like an LCD mount bracket but how do I...
Replies: 9
Views: 346
Posted By diy_in_atl

My bad. The model is samsung me18h704sfs.

My bad. The model is samsung me18h704sfs.
Replies: 9
Views: 346
Posted By diy_in_atl

Samsung OTR Microwave not venting

I have a Samsung OTR microwave that's just over a year old. It looks like the vent motor isn't running. I took the motor out and spun it and it seems like it spins fine. When it runs though, the...
Showing results 1 to 25 of 200
 


 
Forum Jump