Search: Posts Made By: Dilligaff11050
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Replies: 13
Views: 292
Posted By Dilligaff11050

Have you considered taking the transformer for...

Have you considered taking the transformer for the alarm panel and moving it to the plug that the freezer uses? this will give you a system trouble when the freezer loses power whether the system is...
Replies: 11
Views: 218
Posted By Dilligaff11050

If you have 4-wire smoke detectors you can use...

If you have 4-wire smoke detectors you can use the smoke detector power for the glass break detector power. then you can reset the glass break power with the same commands that reset the smoke...
Replies: 7
Views: 194
Posted By Dilligaff11050

If your computer has a wireless network You can...

If your computer has a wireless network You can install a Honeywell thermostat that you can access with a smartphone app. Check with your Gas and Electric provider . The utilities providers often...
Replies: 2
Views: 203
Posted By Dilligaff11050

If you do a factory default you will need to ...

If you do a factory default you will need to
enter zone definitions in sect 001 thru 004
01 delay
03 instant
05 stay/away
07 hardwired smoke detectors

set pgm 1 & 2functions in 009
03 is...
Replies: 9
Views: 701
Posted By Dilligaff11050

If you are testing the system you need to wait...

If you are testing the system you need to wait about 15 to 30 seconds after the exit delay runs out before opening the door. If you are opening the entry door as soon as the exit runs out ( stops...
Replies: 12
Views: 317
Posted By Dilligaff11050

I'm not familiar with Honeywell programming, but...

I'm not familiar with Honeywell programming, but look for for either a stay / away option or force arming. Stay /Away will allow you to arm the panel with the zone tripped, after you exit and the...
Replies: 3
Views: 222
Posted By Dilligaff11050

Have you changed the S/N for the wireless devices...

Have you changed the S/N for the wireless devices for zones 30 & 31 to all zero's and re-boot the system? The problem may be caused by the wireless receiver looking for a device that does not exist.
Replies: 3
Views: 468
Posted By Dilligaff11050

If you cancel monitoring of the existing system...

If you cancel monitoring of the existing system and the company wants to retrieve the existing equipment DO NOT let them remove the equipment. Remove the equipment that they want and put it in a box...
Replies: 6
Views: 336
Posted By Dilligaff11050

I have found DSC equipment listed on ebay.com and...

I have found DSC equipment listed on ebay.com and amazon.com
Replies: 4
Views: 270
Posted By Dilligaff11050

The only way you can mix hard wired and wireless...

The only way you can mix hard wired and wireless devices on the PC1616 and PC1832 is to put the wireless devices on zones 1 thru 8. I suggest moving the wireless devices to zones 1 thru 8 and use...
Replies: 11
Views: 615
Posted By Dilligaff11050

Did you bleed off the air in the pipes? Air in...

Did you bleed off the air in the pipes? Air in the system must be bled off for a hot water system to operate properly.
If you don't have a bleeder at the high point in your system I recommend...
Replies: 7
Views: 403
Posted By Dilligaff11050

On a PC 1616 zones 7 & 8 would be keypad zones...

On a PC 1616 zones 7 & 8 would be keypad zones which are assigned to your keypad. First you need to know which keypad is set-up in slot 1 and 2 in programming section 000. Then go into prog section...
Showing results 1 to 12 of 12


 
Forum Jump