Search: Posts Made By: ahenchmen
Showing results 1 to 25 of 58
Search took 0.01 seconds.
Replies: 7
Views: 9,174
Posted By ahenchmen

Problem solved. Thanks to the simple...

Problem solved.

Thanks to the simple troubleshooting with the fellows here the problem has been solved. At least I believed it has been solved. I believe the issue was nothing more than dirty...
Replies: 7
Views: 9,174
Posted By ahenchmen

puey61, Thanks for the comments and...

puey61,

Thanks for the comments and correcting my terminology. Self propelled mechanisms are not my area. If I have enough daylight at home tonight I'll check if the friction disc is in contact...
Replies: 7
Views: 9,174
Posted By ahenchmen

Puey61, Thanks for the reply. If you...

Puey61,

Thanks for the reply.

If you push the mower forward, it does not roll. If you push the mower backwards, it does not roll. I have a couple movies that I have links below. I wish the...
Replies: 7
Views: 9,174
Posted By ahenchmen

Cheese, Thanks for the tip. I'll take a...

Cheese,

Thanks for the tip. I'll take a closer look at the belt and check for anything obvious.

I'm not sure I understand how a worn belt would prevent the mower from moving forward or...
Replies: 7
Views: 9,174
Posted By ahenchmen

Ariens Mower with Locked wheels on self propelled mower.

I have an Ariens self propelled walk behind mower. I've tried doing some searching on trouble shooting tips but haven't been able to find any good info.

Model: 911516 Serial: 004877

Here is...
Replies: 12
Views: 14,828
Posted By ahenchmen

Just to update everyone with this thread. I've...

Just to update everyone with this thread. I've been a busy and haven't been able to keep up with my internet reply's.

Many thanks to all that have replied. Yes, checking codes is a good thing...
Replies: 4
Views: 3,998
Posted By ahenchmen

Problem solved... A slipped belt. Wouldn't have...

Problem solved... A slipped belt. Wouldn't have been my first guess.

WOW. Sure was noisy!!!

Thanks to all for the quick helpful ideas...
Replies: 4
Views: 3,998
Posted By ahenchmen

Hey now you might be on to something.... I did...

Hey now you might be on to something.... I did notice that the self propel wheels didn't turn when I had them engaged while trying to pull start the mower.

I just pulled off the plastic front...
Replies: 4
Views: 3,998
Posted By ahenchmen

B&S 6.75hp mower engine SCREECH noise

Below are the specs of mower and engine:

21" Troybilt (model 12A-466M011) with B&S 6.75hp engine.

The mower makes a very loud screech noise when the pull chord is pulled quickly or when it runs...
Replies: 6
Views: 10,189
Posted By ahenchmen

Thanks for the comments back. I did finally find...

Thanks for the comments back. I did finally find a little time to disassemble the engine and found a broken rod. Looks like I would need to replace the crank, piston rod, gasket, lower shaft seal...
Replies: 6
Views: 10,189
Posted By ahenchmen

Honda mower run with no oil, rebuild or not?

I have a Honda HR215K1HXA Masters series lawn mower. I think the engine has seized up. Is it worth it dollar wise to rebuild it???

The mower is about 9 years old and looks to be in good...
Replies: 4
Views: 3,875
Posted By ahenchmen

Well just to bring a little closure to the...

Well just to bring a little closure to the subject. I found the problem why the engine would not stop. Turns out to be the cable, it was binding up and not allowing killing the engine. It would...
Replies: 4
Views: 3,875
Posted By ahenchmen

hopkinsr2, Good point about the filter; I'll...

hopkinsr2,

Good point about the filter; I'll try a different one and see if anything changes.

None of the springs are broken and the linkage appears to move freely. I'll play around the with...
Replies: 4
Views: 3,875
Posted By ahenchmen

Let me follow up with additional information and...

Let me follow up with additional information and a question.

I took the bowl off the carb and it looks good. no varnish or debris, some rust but not much.

I've read a few post on reseting the...
Replies: 4
Views: 3,875
Posted By ahenchmen

HONDA HR214 SX LOW IDLE springs or carb?

I have a Honda HR214 lawn mower that runs at a low idle, any ideas why?

History: I got the mower used with unknown history. The mower looks in very good condition, deck shows little wear, engine...
Replies: 12
Views: 14,828
Posted By ahenchmen

Thanks for the tips on how to re-address this...

Thanks for the tips on how to re-address this thread.....


But before I go down that path I need to ask a simple question.

Where is the fuel filter located on a 2002 sienna?

I did a bit of...
Replies: 12
Views: 14,828
Posted By ahenchmen

Since this problem occurs only occasionally (once...

Since this problem occurs only occasionally (once a month or two), should I reply back to this thread or start a new one since this thread might be "old"?
Replies: 12
Views: 14,828
Posted By ahenchmen

the_tow_guy, Thanks for the reply. Someone...

the_tow_guy,

Thanks for the reply. Someone else mentioned the fuel filter as a possible suspect and I'll try that first since's it should be easy to get to.

Regards.
Replies: 12
Views: 14,828
Posted By ahenchmen

Ruff Ideal, I mean rough idle – 2002 Toyota Sienna

I have a 2002 Toyota Sienna minivan with V6 that has been running great until the last many months. Here is what is does… It has been having troubles starting from time to time, specifically a...
Replies: 2
Views: 5,258
Posted By ahenchmen

30yearTech, Thanks for the reply. I was...

30yearTech,

Thanks for the reply.

I was afraid of rust on the inside. I'll see what I can do for this mower.

I did check the compression and it was 90/95psi and spins easily when cranking....
Replies: 2
Views: 5,258
Posted By ahenchmen

Lawnboy Duraforce mower won't start - 2 cycle

I recently came across a LawnBoy mower 10323 mower with a 6.5hp Dura force 2-cycle engine. The problem being that it won't start.

The mower is about 5 years old and unfortunately sat outside...
Replies: 13
Views: 16,532
Posted By ahenchmen

Problem solved! I exchanged the two "new"...

Problem solved!

I exchanged the two "new" rotors back to the auto parts store and paid a few buck more for their premium brand instead of their house brand.

Put the new rotors on and checked...
Replies: 13
Views: 16,532
Posted By ahenchmen

So I finally checked the total run out on the...

So I finally checked the total run out on the rotors and here is what i found.

First I checked the previously turned rotor (right side) and get a total runout of ~.020". :( Next I check the...
Replies: 13
Views: 16,532
Posted By ahenchmen

Here is what I've done thus far... I jacked...

Here is what I've done thus far...

I jacked up each wheel and pushed and pulled it up/down and right left. Up /down had no significant movement. Right and left had some noticeable movement. ...
Replies: 13
Views: 16,532
Posted By ahenchmen

Guy45, Thanks for reply. .0028" sounds...

Guy45,

Thanks for reply. .0028" sounds reasonable. Especially after stumbling across these informative sets of video clips on break/rotor replacements.

What is Rotor Failure? How to Inspect...
Showing results 1 to 25 of 58
 


 
Forum Jump