Search: Posts Made By: biermech
Showing results 1 to 25 of 200
Search took 0.01 seconds.
07-20-20, 05:37 AM
Replies: 7
Views: 341
Posted By biermech

If you would do your research you will find that...

If you would do your research you will find that it is in deed a stenner pump. I posted a picture of the motor assemble because of the gear I mentioned. With 30+ years in water treatment, I have had...
07-20-20, 05:32 AM
Replies: 7
Views: 341
Posted By biermech

https://cimg5.ibsrv.net/gimg/www.doityourselft.com...

https://cimg5.ibsrv.net/gimg/www.doityourselft.com-vbulletin/826x1076/stenner_1_3de9c4ee85e708a61b9e76a0bc8b4e6f15f76eff.jpg
07-19-20, 06:42 AM
Replies: 7
Views: 341
Posted By biermech

If you are referring to the picture I posted,...

If you are referring to the picture I posted, that is a Stenner pump. I have found on several service calls that the phenolic strips causing the rollers not to turn,
07-17-20, 05:45 AM
Replies: 7
Views: 341
Posted By biermech

They use a phenolic gear (#17) that strips,

They use a phenolic gear (#17) that strips,
07-17-20, 05:41 AM
Replies: 7
Views: 341
Posted By biermech

The use a ...

The use a
https://watersoftenersuperstore.com/wp-content/uploads/2015/04/STENNER-GEARS-1.jpg
07-17-20, 05:37 AM
Replies: 1
Views: 123
Posted By biermech

The older systems used a 20 micron sediment...

The older systems used a 20 micron sediment filter. I far as I know the newer ones used a special Kinetico filter. A picture would tell me which you have.
07-16-20, 07:07 AM
Replies: 2
Views: 208
Posted By biermech

While in the service position, disconnect the...

While in the service position, disconnect the brine line at the venture. No water should be coming out. If it does, the figure 8 o ring (7081764) is fault and needs to be replace....
01-23-19, 07:18 AM
Replies: 3
Views: 842
Posted By biermech

WaterSoftenerSuperStore has Kinetico manuals.

WaterSoftenerSuperStore has Kinetico manuals.
01-23-19, 07:15 AM
Replies: 15
Views: 3,611
Posted By biermech

I have not seen where you can program 22 on the...

I have not seen where you can program 22 on the hardness. It use to go to 20 then increments of 5 after that. Here are some possibilities:
1. program is not correct in control panel. Could be set...
01-02-19, 05:31 AM
Replies: 1
Views: 486
Posted By biermech

IIRC the K60 should be a 45 minute regen. Time it...

IIRC the K60 should be a 45 minute regen. Time it is see how long it takes. I would say you would want to clean all flow controls. If you have a partial blockage in the regen flow control, it will...
01-02-19, 05:20 AM
Replies: 2
Views: 1,663
Posted By biermech

The price IMO is way too much. Kinetico's are...

The price IMO is way too much. Kinetico's are nice but you will not be able to find repair parts forcing you to use the local dealer. Labor warranty is usually 1 years which means you would be...
09-24-18, 06:17 AM
Replies: 2
Views: 690
Posted By biermech

Are you still in need of help? I've worked for an...

Are you still in need of help? I've worked for an ECO dealer before and know a lot about there product.
09-24-18, 06:14 AM
Replies: 3
Views: 1,225
Posted By biermech

There is an exploded view of the Kinetico valve...

There is an exploded view of the Kinetico valve that may help on WaterSoftenerSuperStore.
06-20-18, 09:32 AM
Replies: 1
Views: 684
Posted By biermech

You can check to see if the meter is working....

You can check to see if the meter is working. Hold the select button until the screen changes. Hit it until you see 3 000. As water runs through the unit the 000 will change 001, 002, 003. If this is...
06-20-18, 09:25 AM
Replies: 7
Views: 1,013
Posted By biermech

A bad micro switch is a common problem. To check...

A bad micro switch is a common problem. To check to see if the micro switch is functioning properly, press and hold the select button. when the screen changes, press the select button 1 at a time...
06-20-18, 09:17 AM
Replies: 2
Views: 723
Posted By biermech

Turning it backwards should not have hurt...

Turning it backwards should not have hurt anything. The control disc tab will round itself off overtime making it hard to advance into a regen cycle. I say let it be and keep an eye on it before...
05-08-18, 05:33 AM
Replies: 3
Views: 1,188
Posted By biermech

You can find a manual at watersoftenersuperstore.

You can find a manual at watersoftenersuperstore.
04-11-18, 05:28 AM
Replies: 2
Views: 575
Posted By biermech

You haven't said how many people are in the...

You haven't said how many people are in the family. If you are a geek, then the Bluetooth may be fun to have but it will not make your water any better than a plain softener. Look into Clack valves.
04-09-18, 12:49 PM
Replies: 2
Views: 827
Posted By biermech

Salty water to the house has very little to due...

Salty water to the house has very little to due with the seals that were replaced. Salty water is caused by improper backwashing (not enough raise time). It could be a partially blocked drain or too...
03-20-18, 06:26 AM
Replies: 7
Views: 2,228
Posted By biermech

Carbon will not make to water taste less soft....

Carbon will not make to water taste less soft. Whoever, it will make to water taste better by removing chemicals and unwanted taste or odors. There is a reason the system from Amazon is cheaper...
02-24-18, 05:36 AM
Replies: 2
Views: 925
Posted By biermech

Look at the back of the valve. If you see a gray...

Look at the back of the valve. If you see a gray wire attached to the left side of the valve, it's a metered system.
02-24-18, 05:33 AM
Replies: 4
Views: 1,372
Posted By biermech

A direct connection is the only way to use that...

A direct connection is the only way to use that drain. I have done it several time with no issues. It doesn't make it right, but that is the only choice you have short of constructing another drain.
02-22-18, 09:30 AM
Replies: 4
Views: 1,372
Posted By biermech

You can not put an air gap on the 1/2" line. Air...

You can not put an air gap on the 1/2" line. Air gaps are normally use a 1 1/2" pipe.
02-11-18, 05:31 AM
Replies: 1
Views: 979
Posted By biermech

Most likely your 1/2" is 3/4" pex. They do not...

Most likely your 1/2" is 3/4" pex. They do not use 1/2" for the entire house. Buy 3/4" x 3/4" female sharkbite.. Buy 2 3/4" male thread x 1" slip PVC. Buy 2 1" female adaptors. Now you have 1" slip...
01-29-18, 10:27 AM
Replies: 8
Views: 5,432
Posted By biermech

Putting more pressure on the control disc would...

Putting more pressure on the control disc would slow it down or stop it. An easy test before you but a new disc. Use a Phillip's screwdriver and push down on the actuator. Maybe measure the output...
Showing results 1 to 25 of 200
 


 
Forum Jump