Search: Posts Made By: Ray Odom
Showing results 1 to 25 of 119
Search took 0.01 seconds.
Replies: 2
Views: 432
Posted By Ray Odom

Engine sputters and dies

Without warning my 2000 Chrysler Town &Country, 200000 miles started sputtering, slowing down, and eventually died. It would restart and idle good, then drive ok for a few feet or so, and fail again....
Replies: 11
Views: 702
Posted By Ray Odom

Turned out to be the fuel pump that had been...

Turned out to be the fuel pump that had been installed several weeks ago. Thanks for your suggestions.
Replies: 11
Views: 702
Posted By Ray Odom

Good idea. What would be a good item for creating...

Good idea. What would be a good item for creating smoke?
Replies: 11
Views: 702
Posted By Ray Odom

Understood. Had an idler pulley go out one time...

Understood. Had an idler pulley go out one time and it was a rattle, not a bearing type noise and sounded like one side of engine, but was on other side. Haven't been able to get back to it yet.
Replies: 11
Views: 702
Posted By Ray Odom

Engine is transverse with exhaust outlet and...

Engine is transverse with exhaust outlet and transmission on driver's side. However, it seem I can hear noise better outside car on passenger side. Noise is very deceptive. Haven't had a chance to...
Replies: 11
Views: 702
Posted By Ray Odom

Thx, I'll give it a good look.

Thx, I'll give it a good look.
Replies: 11
Views: 702
Posted By Ray Odom

Humming noise

I have a 2000 Chrysler Town & Country with 190000 miles on it. Just last week it developed a strange humming noise that I can't locate. One might even call it a low roar, but not an exhaust roar. At...
Replies: 4
Views: 567
Posted By Ray Odom

Chandler, that is exactly the way mine works....

Chandler, that is exactly the way mine works. I've done it like you and to no avail. Maybe the answer is to switch fobs with my wife ��
Replies: 4
Views: 567
Posted By Ray Odom

Sorry, but thought saying reprogrammed was...

Sorry, but thought saying reprogrammed was sufficient to say that I had followed instructions in the manual to reprogram. This is not something I've just tried once or twice, but many times over the...
Replies: 4
Views: 567
Posted By Ray Odom

Programmed Mirrors

I have a 2000 Chrysler Town and Country Minivan that has programmable mirrors. The mirrors cannot successfully be reprogrammed to work with the inside door switch or the number 1 remote. Driver side...
Replies: 3
Views: 499
Posted By Ray Odom

Amana Icemaker Line

Thanks for your reply. Found fill line frozen at icemaker and know the input valve is leaking causing the problem. Replacing valve.

Not sure how to claim problem solved for this thread.
Replies: 3
Views: 499
Posted By Ray Odom

Amana Icemaker Line

The plastic line going into the icemaker won't stay in. It is just a slip=in line that goes into a rubber fitting and held in place with a squeeze clamp. Icemaker makes ice just fine, not hollow...
Replies: 14
Views: 987
Posted By Ray Odom

Marjob, just doing rear. Too tired after that...

Marjob, just doing rear. Too tired after that one, finish tomorrow. One problem I had after getting compression tool was the rubber "boot" wanted to wrinkle up and I had to do it in spurts to allow...
Replies: 14
Views: 987
Posted By Ray Odom

Fixed

Just not "hoss" enough to push it in with c clamp. Borrowed tool from Aotozone and it worked. Still took 12" crescent and a 12" breaker bar in other hand to get it in. Thx for help.
Replies: 14
Views: 987
Posted By Ray Odom

Did that. Didn't help, but thanks.

Did that. Didn't help, but thanks.
Replies: 14
Views: 987
Posted By Ray Odom

Disc Brakes

Attempting pad replacement on 2000 Nissan Maxima. Can't seem to collapse piston in order to reinstall caliper onto rotor. All I've ever on worked on before collapsing was easy with c clamp. Help,...
Replies: 5
Views: 2,083
Posted By Ray Odom

Thank you. I wondered if that might be the case....

Thank you. I wondered if that might be the case. I will check out promptly.
Replies: 5
Views: 2,083
Posted By Ray Odom

Yes, I know I can probably have it read, but...

Yes, I know I can probably have it read, but thought it might be a typical light designed to go off at a specific number of miles and someone might just know what it was. Will try to have code read...
Replies: 5
Views: 2,083
Posted By Ray Odom

Service soon light

My 2000 Nissan Maxima has a v6 engine of 182 cu. in. with 65800 miles on it.
Yesterday a light came on that says Service Engine Soon. This does not say Check Engine which seems to be the customary...
Replies: 3
Views: 28,194
Posted By Ray Odom

Chromecast and iPad 1

Google says the Chromecast requires IOS 6.0 or better which will not work on Ipad 1. However, the app for IOS says it was developed for IOS 5.1.1 or better. Does that mean the IPad 1 using IOS 5.1.1...
Replies: 1
Views: 688
Posted By Ray Odom

mv4 file conversion

I HAVE A RSS FEED THAT HAS VIDEOS IN .M4V FORMAT THAT I WOULD LIKE TO DOWNLOAD, CONVERT AND BURN A DVD FOR PLAYING ON MY TV AND COMPUTER. I HAVE USED "ANY VIDEO CONVERTER" TO CONVERT TO .MP4 FORMAT...
Replies: 4
Views: 8,736
Posted By Ray Odom

Not Motor mounts

Thanks for your reply, but I had motto mounts replaced for engine shake and that didn't fix this particular problem. It seems to be more of a drive line problem than engine shaking. I think?
Replies: 4
Views: 8,736
Posted By Ray Odom

Pt Cruiser vibration.

My daughter's Cruiser has a mysterious vibration while accelerating. It is most noticeable in second gear, but continues after shift, if accelerating. The whole car seems to shake and sometimes feels...
04-20-13, 03:40 PM
Replies: 3
Views: 2,620
Posted By Ray Odom

It's complicated. I had vinyl tile over the...

It's complicated. I had vinyl tile over the ceramic and it was glued tightly. Ceramic was diagonal on floor and this results in ragged hole, zig-zag type. Hole is about 3ftx3ftx1/4in. I think you...
04-20-13, 01:56 PM
Replies: 3
Views: 2,620
Posted By Ray Odom

Self Leveling Underlayment

I have had a drain leak and the ceramic tile covered concrete floor was jack-hammered. They filled the hole to within 1/4", but now I have to level it so I can lay new 1 piece vinyl tile over entire...
Showing results 1 to 25 of 119
 


 
Forum Jump