Search: Posts Made By: Bernard_01
Showing results 1 to 25 of 200
Search took 0.01 seconds.
03-29-19, 04:29 AM
Replies: 3
Views: 466
Posted By Bernard_01

Is there a special type receptacle I should...

Is there a special type receptacle I should purchase.....it doesn't mention where the receptacle should be located...(ceiling, wall , unit mounted, etc. )? Im guessing here but I'm pretty sure...
03-28-19, 06:34 AM
Replies: 3
Views: 466
Posted By Bernard_01

Century Patriot 80 low boy oil fired

greetings, I just purchased century patriot low boy oil fired hot air furnace. 95K btu. I was surprised to see that it came with a pre installed cord that just plugs into a dedicated 15amp...
10-04-13, 06:49 AM
Replies: 3
Views: 752
Posted By Bernard_01

ty

thank you mr. grady.......you always give me the correct anwers !
10-03-13, 09:42 AM
Replies: 3
Views: 752
Posted By Bernard_01

275 gl oil tank question

Old fisherman here in New Hampshire,
I am installing a new horizontal oil tank from the Depot. The accessory kit is sold separately. It will draw from the top. At the bottom, do I still need...
07-29-13, 05:16 AM
Replies: 1
Views: 789
Posted By Bernard_01

electric water heater

good morning from new Hampshire,
I will be relocating my electric hot water tank to another part of the house. can I extend the present circuit using a j-box and splicing from the original...
05-10-13, 11:15 AM
Replies: 2
Views: 605
Posted By Bernard_01

conductor size for panel

Greetings from NH,

A mobile home is wired with NM cables. The inside older fuse box (screw type) has a main breaker(outside) of 50A . The conductors coming to the fuse box from outside are #6. ...
12-01-12, 05:07 PM
Replies: 7
Views: 1,453
Posted By Bernard_01

so, i will change the 3 prong receptacle for a 4...

so, i will change the 3 prong receptacle for a 4 prong receptacle. the new circuit fron the panel will have 4 wires. i will eleiminate the bonding strap on the appliance, and i will run cable...
12-01-12, 04:33 PM
Replies: 7
Views: 1,453
Posted By Bernard_01

so, those two little nubs will fit into 2...

so, those two little nubs will fit into 2 existing (empty) holes on the neutral bar?

At the range the neutral screw and the ground screw are bonded together with a copper strap.

My...
12-01-12, 03:59 PM
Replies: 7
Views: 1,453
Posted By Bernard_01

#6AWG neutral conductor will not fit on bar

greetings again from NH,

I installed a new electric range and the #6awg neutral conductor does not seem to fit into the provided hole in the neutral bar at the panel. Can you pros suggest a...
10-25-12, 07:10 AM
Replies: 3
Views: 842
Posted By Bernard_01

hi, so the new 14/3 w/ground would come from...

hi, so the new 14/3 w/ground would come from the existing ceiling light and then I can install 2 single pole switches in a double gang box from this 14/3? One switch would be used for the exisitng...
10-25-12, 05:16 AM
Replies: 3
Views: 842
Posted By Bernard_01

Missing a neutral?

greetings from new hampshire,

my hallway ceiling light is controled by a single pole switch loop. one cable enters the switch box. the white conductor is always hot on the top screw of the...
11-16-11, 01:07 PM
Replies: 2
Views: 762
Posted By Bernard_01

cable question

greetings from NH once again.

I will be installing a 240V single section of electric baseboard heat. The cable feeding this heater is NM 12-2 with ground. The breaker is a 20A DP breaker. The...
11-08-11, 04:43 AM
Replies: 2
Views: 648
Posted By Bernard_01

Cables & Studs

Greetings again from new hampshire..it's always a pleasure to visit the forum.
When running cable in a new constuction additon room,
I know I have to apply the red fire stop caulk at the bottom...
10-20-11, 10:59 AM
Replies: 1
Views: 756
Posted By Bernard_01

how big a hole ?

Greetings again from NH.

I need to pull 3 NM cables (NM14 NM14 NM12). They will pass thru my 2" x 6" wooden wall studs (exposed at present). What size spade bit should I use in the center of...
Replies: 9
Views: 1,103
Posted By Bernard_01

Thank you Bud. I do have access to the...

Thank you Bud. I do have access to the machine. 15 bags @ 2.2 cu. ft.
Replies: 9
Views: 1,103
Posted By Bernard_01

yes it is an addition on posts. the crawl space...

yes it is an addition on posts. the crawl space will have a skirt around the 3 open sides.
thanks.
Replies: 9
Views: 1,103
Posted By Bernard_01

no it is not.....open to the elements. Plastic...

no it is not.....open to the elements. Plastic is spread on the ground underneath the room.
Replies: 9
Views: 1,103
Posted By Bernard_01

there is a plywood bottom attached to the...

there is a plywood bottom attached to the joists....then a crawl space.
Replies: 9
Views: 1,103
Posted By Bernard_01

insulation between joists

hi again....my new floor joists are 2 x 10's. the sub floor has not been put down yet. what type of insulation should i be looking at? batts or loose fill that i can just pour in? thanks.
Replies: 2
Views: 2,194
Posted By Bernard_01

Birds mouth cut ?

greetings again from NH....
Roof rafters span 11' 6" over the bearing walls constructed of 6" x 6" 's.
This is technically a shed style roof with the inside bearing wall standing 7' 7" and the...
Replies: 4
Views: 1,309
Posted By Bernard_01

sorry about my lack of specifics. my footings...

sorry about my lack of specifics. my footings and posts (attached to footings) are already installed. i need to build my beam (to connect to the posts with "shoulder cut notched posts". the...
Replies: 4
Views: 1,309
Posted By Bernard_01

post & beam placement

greetings, my 6 x 6 posts are on footings spaced on center at 0 - 7.5' - 7.5' - 10.5'

I plant to build this beam using 2x10's.

my plan is for [email protected] feet and [email protected] 12 feet.

...
Replies: 1
Views: 1,009
Posted By Bernard_01

porch ceiling rafter question

Greetings from NH once again,
Hurricane Irene has come and gone....thank goodness no damage here for me. I would like to extend the outer wall of my covered deck another three feet into the yard. ...
Replies: 4
Views: 3,758
Posted By Bernard_01

simpson fasteners

hi lefty, thanks for the advice on the fasteners. I look forward to getting them this weekend. although they are predicting a foot of snow here this weekend. :NO NO NO:
Replies: 4
Views: 3,758
Posted By Bernard_01

beam

thank you lefty for your expertise. approximately what is the difference between ordering LVL;S pre fabbed to size v. making these beams myself from pressure treated lumber?

thanks Bob
Showing results 1 to 25 of 200
 


 
Forum Jump