Search: Posts Made By: jac1987
Showing results 1 to 25 of 38
Search took 0.01 seconds.
Replies: 5
Views: 647
Posted By jac1987

Hello all, The reason why I’m moving to...

Hello all,

The reason why I’m moving to Wireless is because my house is an old house (25+ years) and the cabling was done over the walls exposed to plain sight, some ducting was used to cover the...
Replies: 5
Views: 647
Posted By jac1987

Wireless replacement for

Hi,

My system is power series 1832. Im looking to go all Wireless, the only ones I need to replace for Wireless sensors are a couple of LC-104-PIMW but I dont seem to find a Wireless alternative...
Replies: 7
Views: 4,563
Posted By jac1987

I set up something similar for my home alarm...

I set up something similar for my home alarm system, I have an envisalink with a pc1832 and some ip cameras. I wanted to be able to keep monitoring my alarm and cameras even when the main internet...
Replies: 7
Views: 2,955
Posted By jac1987

a ok, I have mostly Dsc and one Honeywell motion...

a ok, I have mostly Dsc and one Honeywell motion sensor and both have that slot but it is good to know all this. Thanks again for the help.
Replies: 7
Views: 2,955
Posted By jac1987

Thanks for the confirmation, I have wired the...

Thanks for the confirmation, I have wired the other sensors just like this one and everything is working fine.

Now, just for general knowledge, on which situation do you use plug something on the...
Replies: 7
Views: 2,955
Posted By jac1987

Yes I know, autocorrect on my phone didnt help,...

Yes I know, autocorrect on my phone didnt help, also, posting past midnight didnt help either.

here is the pic also68866
Replies: 7
Views: 2,955
Posted By jac1987

Using resistors correctly in alarm system

I have a Dsc pc1832 that runs wireless sensors for doors and motion detector except two wired sensors, I just changed some of the wireless sensor for wired an re located the wireless sensors.

At...
Replies: 6
Views: 630
Posted By jac1987

This is hard to accomplish on a vista20p yet easy...

This is hard to accomplish on a vista20p yet easy on dsc pc1832, I just found out now that I hooked the old vista20p on my parents house.
Replies: 4
Views: 909
Posted By jac1987

Thanks again for your help, turn out that what I...

Thanks again for your help, turn out that what I really needed/wanted was disable the delay on notifications
Replies: 4
Views: 909
Posted By jac1987

Thanks for the information, I thin I will go with...

Thanks for the information, I thin I will go with tour recommendation and not be lazy and run the cable all the way to the panel.

Another question on the reporting section 320 and the other after...
Replies: 4
Views: 909
Posted By jac1987

How to wire zone to keypad

I finally got the system working the way I want but I saw something on the manual I would like to use.

Panel DSC Pc1832 v4.2
keypad PK5500
type of zone I want to wire to the keypad: LC-100-PI...
Replies: 10
Views: 5,007
Posted By jac1987

So what I have to do is 1. Wire the new keypad...

So what I have to do is
1. Wire the new keypad following the existing color code
2. Go to section 000 and then 0
3. Enter 1 since I have only one partition
4. The set slot assignment, say I...
Replies: 10
Views: 5,007
Posted By jac1987

You were more tha right is to much hassle, I...

You were more tha right is to much hassle, I tried different downloads, drivers even different usb to serial adapter and nothing worked.

Quick question, I'm about to get a keypad pk5500 to replace...
Replies: 10
Views: 5,007
Posted By jac1987

thanks for the confirmation, ive seen a couple of...

thanks for the confirmation, ive seen a couple of videos but just realized this is not simple at all.

this is what I have.

-the pclink bought from Amz
-serial to usb cable
-dls5 (just updated...
Replies: 10
Views: 5,007
Posted By jac1987

**sorry for the mess, adt decided to use the...

**sorry for the mess, adt decided to use the smallest box they could find and throw everything inside.
Replies: 10
Views: 5,007
Posted By jac1987

thanks for your answer, this is a pic of my...

thanks for your answer, this is a pic of my board, as you can see the COM2 port looks like the one you mentioned, Im a little confused because ive seen on youtube videos boards with an actual pclink...
Replies: 10
Views: 5,007
Posted By jac1987

About PCLINK and PC1832

Im planning to get a PClink cable to use with dls5 to manager alarm and to get going a new one for my parents, on my board a pc1832 v4.24NA (I think) dont have a PCLINK connector (PINS) as I have...
Replies: 4
Views: 6,132
Posted By jac1987

Thanks for that info, I had no idea about that,...

Thanks for that info, I had no idea about that, will change the zone type as you suggested. Thanks again.
Replies: 4
Views: 6,132
Posted By jac1987

thanks for the answer, but disabling the stay...

thanks for the answer, but disabling the stay sensor will not work on my scenario.
Replies: 4
Views: 6,132
Posted By jac1987

DSC - how to disable auto stay?

I want to be able to disable the auto stay function.

Is there a way I can disable this so every time I arm away it goes into that mode rather to arm stay because I never open closed a door.

...
Replies: 5
Views: 1,163
Posted By jac1987

Alright now I get how it works. One last...

Alright now I get how it works. One last question, is it normal that both 403 and 404 have the exact same code?
Replies: 4
Views: 1,540
Posted By jac1987

great thanks, works great, power cycle the panel...

great thanks, works great, power cycle the panel and no more clicking sounds
Replies: 5
Views: 1,163
Posted By jac1987

Thanks for pointing to the right direction, dont...

Thanks for pointing to the right direction, dont want to abuse on your help but this is what I got following the process based on the manual

- means nothing was displayed

one number was shown...
Replies: 5
Views: 1,163
Posted By jac1987

Get codes from DSC at sections 403 and 404 with keypad pk5500

I just bought the cable and downloaded DSL5 to check on programing for a panel dsc pc1832.

Part of the process shows that I will need 2 codes in order to establish the connection, the codes are...
Replies: 4
Views: 1,540
Posted By jac1987

yes, it is a DSC PC1832. Since I have the...

yes, it is a DSC PC1832.

Since I have the installer code and it is indeed the correct installer code, is there a way to disable the installer lockout?.
Showing results 1 to 25 of 38
 


 
Forum Jump