Search: Posts Made By: jem8745
Showing results 1 to 20 of 20
Search took 0.01 seconds.
Replies: 7
Views: 11,234
Posted By jem8745

Well I have traced the problem to the turn signal...

Well I have traced the problem to the turn signal switch or the multi-function switch. Does anyone have any expertise with this piece of hardware, and how to remove or repair it?
Thanks
Replies: 7
Views: 11,234
Posted By jem8745

I do not find a fuse box under the hood. And yes...

I do not find a fuse box under the hood. And yes the hazard lights do not work.
Replies: 7
Views: 11,234
Posted By jem8745

'97 chevy blazer no brake lights or hazards

The brake lights on this 1997 Chevy Blazer stopped working along with the hazard lights. The CENTER BRAKE light works, the turn signals work, parking lights work, tail lights work. However when the...
Replies: 1
Views: 2,736
Posted By jem8745

1991 Buick Park Ave. water pump removal

I am trying to remove the water pump on my 1991 buick park ave. On the right hand side facing the pump are two 13mm bolts. they must are only accesable by use of a socket. one is accecable with a...
Replies: 5
Views: 3,435
Posted By jem8745

Master cylinder

After New calipers, new rubber brake hose, and having the ABS almost half disconected we discovered the the new master cylinder, that was but a few months old had failed in the first stage. It...
Replies: 5
Views: 3,435
Posted By jem8745

I have replaced the ruber hose to the front...

I have replaced the ruber hose to the front caliper, and that has not solved the problem, I don't find a proportioning valve.
Still the Right front and Left rear brakes are thght. The piston in...
Replies: 5
Views: 3,435
Posted By jem8745

"91 Buick Park Avenue Brake Problem

On my 1991 Buick park ave. equipped with ABS the Front passenger caliper and the driver side rear drum brake will not relax after taking foot off of brake petal. I thought the caliper was froze and...
Replies: 7
Views: 3,655
Posted By jem8745

I believe I found the problem, it seems as though...

I believe I found the problem, it seems as though there was a bleeder screw at a rear wheel cylinder that was not seating properly. Although there was no fluid leaking, there seemed to be a air...
Replies: 7
Views: 3,655
Posted By jem8745

I am pretty sure I understand the bench bleeding...

I am pretty sure I understand the bench bleeding process however on the left side of the master cylinder reservoir, as you look at it from the front of the car, is a rubber hose that is connected to...
Replies: 7
Views: 3,655
Posted By jem8745

Bleeding brakes on 1991 buick Park ave.

Recently replaced the master cylinder on my Park Ave.. I am having trouble bleeding the brakes.
When I changed the master cylinder I was unable to bench bleed as instructed as the rubber hose...
Replies: 1
Views: 818
Posted By jem8745

1991 Buick Park Ave.

I have a '91 buick Park Ave, occasionally when first started the transmission will not engage. I must move the shift selector all of the way to the 1st gear position for the trans. to engage. After...
Replies: 5
Views: 2,538
Posted By jem8745

'99 dodge dakota front wheel bearing

I am unhappy to report that this bearing is not rebuidable. The bearing race is actually part of the casting, therein lies the problem as the race is the weak link, rather soft with a very thin...
Replies: 5
Views: 2,538
Posted By jem8745

I guess it's just my nature to try and repair,...

I guess it's just my nature to try and repair, rather than replace the complete unit. Besides this unit is upwards of $200 in my area for the inexpensive aftermarket product.
Replies: 5
Views: 2,538
Posted By jem8745

1999 Dakota Front wheel bearing hub assembly

I have a 1999 Dodge Dakota 4-wheel drive manual transmission with a 3.9 v-6 engine. The front wheel bearings are bad.
Is it possible to rebuild the front wheel bearing hub assembly? i.e. pressing...
Replies: 2
Views: 853
Posted By jem8745

torque requirement

I am replacing a front, wheel bearing hub assembly on a 1991 Buick Park Avenue. I need the torque specifications for the axle nut.

Thanks for the help. Jim
Replies: 4
Views: 948
Posted By jem8745

Had code read, possible crankshaft sensor,...

Had code read, possible crankshaft sensor, camshaft sensor, PCM.
Intermittent problem, four days later and a few hundred dollars it was determined to be the crankshaft sensor. It was replaced and...
Replies: 4
Views: 948
Posted By jem8745

1999 Dodge Dakota 3.9

I have a 1999 Dodge Dakota 3.9 engine 5 speed standard trans. 4wd 125000 miles. Have developed a miss. Changed plugs, wires, distributor cap and rotor, has not helped. Doesn't miss when first...
Replies: 5
Views: 2,371
Posted By jem8745

Thanks for the advice, will check out the fuel...

Thanks for the advice,
will check out the fuel system first, before we start looking at electrical.
Replies: 5
Views: 2,371
Posted By jem8745

Hard start

Cranks with correct speed, however more times than not it cranks longer than I am accustomed to. Sometimes it cranks as long as long as 5 seconds or longer before it fires. It doesn't seem to make...
Replies: 5
Views: 2,371
Posted By jem8745

1991 buick lesabre hard starting

I have a '91 lesabre with 3.8 engine with 49000 miles. It runs good however it is getting to be a hard starter. Have replaced the plugs, a bad water pump, checked wires for possible leaks. The...
Showing results 1 to 20 of 20


 
Forum Jump