Search: Posts Made By: 7magg
Showing results 1 to 25 of 54
Search took 0.01 seconds.
09-27-10, 07:46 AM
Replies: 5
Views: 6,901
Posted By 7magg

The problem is when using fiberglass mesh tape,...

The problem is when using fiberglass mesh tape, it is best to use the powder type mud like durabond 90, or durabond 45. this is a much harder mix then the premixed when dry. Before I tape drywall I...
Replies: 5
Views: 6,739
Posted By 7magg

Exclamation Thanks guys. I am not sure what I did, but the...

Thanks guys. I am not sure what I did, but the pump has been stopping since I last messed with it. The old tank was drained and I checked the pressure and it had none, I filled it to 18 lbs and after...
Replies: 5
Views: 6,739
Posted By 7magg

Well I was eager to fix the problem, so I went...

Well I was eager to fix the problem, so I went out and bought a new tank, a 36 gallon, I thought the original was the same but instead it was a 20 gallon! I hooked it up and the pump is doing the...
Replies: 5
Views: 6,739
Posted By 7magg

jet well pump will not stop

Hello, my jet pump will not stop running! I tried to adjust the spring then it shut off but when it turns on it still runs constant! I drained the tank till no pressure and checked it with tire gage...
Replies: 12
Views: 1,174
Posted By 7magg

You live in a nice area, I went a year at Ferris...

You live in a nice area, I went a year at Ferris State. So in any well that smells like egg water it is because of bacteria? What is the easiest way to add? there are two elbows that have straps,...
Replies: 12
Views: 1,174
Posted By 7magg

Thanks again for the info greenguy, I live in...

Thanks again for the info greenguy, I live in Tecumseh about 40 minutes south of AnnArbor. The bleach down the well sounds like it will work, But I don't know which pipe to try to put it in? with...
Replies: 12
Views: 1,174
Posted By 7magg

Thanks greenguy, We bought a fixer upper on a...

Thanks greenguy, We bought a fixer upper on a beautiful pond, loaded with monster bass!! nobody but me fishes it. So the caps are usually in two pieces, I did'nt know, the pic didn't show how the...
Replies: 12
Views: 1,174
Posted By 7magg

Sorry guys, The lid was frozen shut!! :D The...

Sorry guys, The lid was frozen shut!! :D The little bit of sun today helped it thaw. It might be hard to tell from the down ward shot but the top is in two pieces that are sitting on top of well...
Replies: 12
Views: 1,174
Posted By 7magg

No it did not freeze, and it's not leaking. We...

No it did not freeze, and it's not leaking. We bought a repo house and the pump was bad, we had the bank buy a new well pump before we bought the house, so they found a dude in the area and I assume...
Replies: 12
Views: 1,174
Posted By 7magg

well & jetpump question

Hello, I notice in our well pit, where the jet pump is conected to the pipe that goes into our well, the top is broken. The old top is metal and has a notch that goes around the water pipe, but it is...
03-03-08, 08:05 AM
Replies: 4
Views: 935
Posted By 7magg

I would say a texture would be less work, unless...

I would say a texture would be less work, unless you are a profesional drywaller! you would need a few coats to smooth it out then sanding over head:thumbdn: you can rent or buy a $40 sprayer some...
02-29-08, 07:19 PM
Replies: 2
Views: 1,024
Posted By 7magg

how is your floor built? what size joist and...

how is your floor built? what size joist and spacing? I have seen this many times with cheap builders spacing 18" on center! you might be able to add bridging to help stiffen.
02-29-08, 07:13 PM
Replies: 4
Views: 935
Posted By 7magg

I use a floor scaper and a pump sprayer to wet...

I use a floor scaper and a pump sprayer to wet the popcorn, this helps cut down on dust and makes it easier. You can spray knock down to texture, I have done both an orange peel and a heavy texture...
Replies: 32
Views: 1,377
Posted By 7magg

Still wondering if I could see the picture?:D

Still wondering if I could see the picture?:D
Replies: 32
Views: 1,377
Posted By 7magg

If you would please, a picture would help me...

If you would please, a picture would help me greatly. would I need pressure valves or check valves?
Replies: 32
Views: 1,377
Posted By 7magg

thanks nj, I believe there is only one...

thanks nj, I believe there is only one transformer. So I would be better off adding another transformer to my present system? on my present manifold if I T off and add the floor zone, I would need a...
Replies: 32
Views: 1,377
Posted By 7magg

where did everybody go?

Hey guys I'm missing ya!:D don't give up on the thread!!
Replies: 32
Views: 1,377
Posted By 7magg

nj I added some pics of our boiler, it's in it's...

nj I added some pics of our boiler, it's in it's second year with no problems. :) I still don't know how to add pics to the thread sorry; photobucket-7magg+:D
...
Replies: 32
Views: 1,377
Posted By 7magg

Hey fellas don't forget me!!:D If I come off my...

Hey fellas don't forget me!!:D If I come off my boilers manifold and work a system like nj's 3rd drawing (last one) without the pump, where in reation to mixing valve would the zone valve go?
Replies: 43
Views: 2,400
Posted By 7magg

I think having it a seperate zone would be best,...

I think having it a seperate zone would be best, you are right the aluminum plates are expensive!! sure do add up quick. a seen a site where a guy made his own plates out of aluminum soffit and a jig...
Replies: 43
Views: 2,400
Posted By 7magg

Thanks guys I really appreciate the food for...

Thanks guys I really appreciate the food for thought!! I was wondering if a T after the zone valve would starve the main loop? there is an 1 1/4 copper maniflod out of the boiler with 4 zone valves...
Replies: 43
Views: 2,400
Posted By 7magg

Hey thanks trooper that site looks interesting! I...

Hey thanks trooper that site looks interesting! I had a quote from another company who makes grills for comercial building the bid was $400 for a section 8'x 4", I was surprised! I am half tempted to...
Replies: 43
Views: 2,400
Posted By 7magg

I don't mean to repeat questions but some have...

I don't mean to repeat questions but some have not been answered? Infloor on same zone? would i tie it in the same loop, the zone is basically a big rectangle starting in one corner closer to...
02-16-08, 08:22 AM
Replies: 4
Views: 1,774
Posted By 7magg

I did think of tying it to boiler, but the room...

I did think of tying it to boiler, but the room is off the garage. I would have to bust block, cut a trench in the concree floor and more nonsense to get it run in.
Replies: 43
Views: 2,400
Posted By 7magg

Thank you so much trooper great feedback. I did...

Thank you so much trooper great feedback. I did look into what warmboard is "$" It should be prefinished for that much!! The product sounds good but would there be and headaches on layout of the...
Showing results 1 to 25 of 54
 


 
Forum Jump