Search: Posts Made By: mkdsk
Showing results 1 to 25 of 31
Search took 0.01 seconds.
Replies: 5
Views: 797
Posted By mkdsk

Tv

What is making the TV click when it is off?
Replies: 5
Views: 797
Posted By mkdsk

Hello

No I don't but the TV is not that old.
Replies: 5
Views: 797
Posted By mkdsk

Television

I have a Sanyo TV and when the TV is off I hear a clicking sound coming from the TV. It is model number DS32424. Any ideas why it is clicking when it is turned off?
Replies: 7
Views: 1,539
Posted By mkdsk

tv

I posted the model number. Can anyone help?
Replies: 7
Views: 1,539
Posted By mkdsk

It is model number DS32424. Any ideas why it is...

It is model number DS32424. Any ideas why it is clicking when it is turned off?
Replies: 7
Views: 1,539
Posted By mkdsk

Tv

does it matter what model number it is?
Replies: 13
Views: 11,492
Posted By mkdsk

Pressure Valve

I have this same problem with my boiler going up to 30 PSI when my boiler runs. Can someone runs me through on how to adjust the pressure valve. Thanks.
Replies: 5
Views: 802
Posted By mkdsk

Thermostat

What would be the best way to get a wire to the 2nd floor to hook to a thermostat? Any ideas?
Replies: 5
Views: 802
Posted By mkdsk

Thermostat

I want to install a thermostat on my second floor of my house. Can I just run the thermostat wire from my basement to the outside and up to the 2nd floor? Will it hurt that the wire is outside? ...
12-09-08, 03:40 PM
Replies: 7
Views: 2,021
Posted By mkdsk

thermostat

The receiver is the part that gets hooked up to wall where the old thermostat was. The wireless thermostat is the part that I can take to any room I go in to.
12-09-08, 07:30 AM
Replies: 7
Views: 2,021
Posted By mkdsk

Thermostat

It is a WIRELESS thermostat. The receiver doesn't have batteries only the thermostat does. The receiver needs to be wired to get 24VAC continuous power but there are only two wires going to my old...
12-08-08, 06:19 PM
Replies: 7
Views: 2,021
Posted By mkdsk

WIRELESS Heat thermostat

I have the RH and RC jumped and I have the red wire connected to the RH and the white wire connected to to the W just like my old thermostat was. Are you saying connect another wire to the C and the...
Replies: 4
Views: 875
Posted By mkdsk

Boiler

The pressure when the system is cold is about 14 or 15 psi. Is that normal? Also, when I installed the expansion tank I put 12 psi in it then I refilled the system. What else could be making the...
12-08-08, 06:01 AM
Replies: 7
Views: 2,021
Posted By mkdsk

Thermostat

I have the Wistat T50-series WIRELESS Heat thermostat and receiver. I am trying to hook up the wires to the receiver but I am getting no power to it. I put the receiver where my old thermostat was...
Replies: 4
Views: 875
Posted By mkdsk

Furnace

My furnace is going to 30 PSI when the heat runs. I replaced the expansion tank and it is still going to 30 PSI. The valve where the water comes to the furnace from the is brand new but still may be...
Replies: 7
Views: 1,539
Posted By mkdsk

Tv

Of course if I unplug the TV the noise stops. I plug it back in it makes the noise again. It is a Sanyo TV. Nothing more to tell you about it.
Replies: 7
Views: 1,539
Posted By mkdsk

Sanyo TV

I have a Sanyo TV and when the TV is off I hear a clicking sound coming from the TV. Anyone know what that could be?
Replies: 1
Psi
Views: 840
Posted By mkdsk

Psi

What should the PSI be when the furnace is running and what should it be when the furnace is not running? Thanks.
Replies: 13
Views: 1,852
Posted By mkdsk

Boiler

Another question for you. I checked the air pressure in the expansion tank and it it at 15. Shouldn't it only be at 12? Also, my expansion tank is connected to a red device and on it it says "Taco...
Replies: 13
Views: 1,852
Posted By mkdsk

Boiler

You said with system cold, close the shutoff valve to the pressure reducing valve and relieve the boiler pressure to @12 to 15 psi. How do I reduce the pressure to 12-15 psi? Do I drain some water...
Replies: 8
Views: 1,008
Posted By mkdsk

Tank

How do I check the air pressure in the expansion tank? I don't see anyplace to check it?
Replies: 13
Views: 1,852
Posted By mkdsk

Boiler

I am just going to replace the expansion tank. It is still under warranty so what could it hurt. ANYONE ELSE KNOW WHAT COULD BE MAKING THE BRAND NEW RELIEF VALVE still drip when I turn up my...
Replies: 13
Views: 1,852
Posted By mkdsk

boiler

It does have a Schrader (tire) valve on it. But if I wanted to replace it can I do it myself? What else would be making the boiler PSI go up too high?
Replies: 13
Views: 1,852
Posted By mkdsk

Boiler

The relief valve was replaced a few weeks ago and the expansion tank was checked and the right amount of air was put in it. I was told to keep an eye on the boiler to make sure everything was okay. ...
Replies: 13
Views: 1,852
Posted By mkdsk

Boiler

When it gets hot it is less then 20 psi. When I turn the heat up it goes over to about 30 psi. I already replaced the relief valve. What can I do to fix this problem?
Showing results 1 to 25 of 31
 


 
Forum Jump