Search: Posts Made By: WeldGod
Showing results 1 to 25 of 200
Search took 0.02 seconds.
09-15-05, 09:40 AM
Replies: 7
Views: 1,668
Posted By WeldGod

Two guns come to my mind. The first one is the...

Two guns come to my mind. The first one is the Winchester Model 70 Stealth. I have shot Sub M.O.A. groups with it out to 500 yards. I also like the Savage 12 Series Varmint I shot a .77 group with it...
09-08-05, 07:12 PM
Replies: 2
Views: 732
Posted By WeldGod

Trees can be planted up to time of first frost....

Trees can be planted up to time of first frost. If the first frost has already occurred you will need to plant your trees in a climate controlled area and transplant next spring after the last freeze.
09-06-05, 08:23 PM
Replies: 1
Views: 688
Posted By WeldGod

Turing white could be a number of things. It...

Turing white could be a number of things. It could be a fungus. The fungus is not a big deal. Lilacs are epically prone to fungus. If the spots will not wipe off. Spray the leaves with a fungi side. ...
09-05-05, 04:40 AM
Replies: 1
Views: 928
Posted By WeldGod

One of the first things to suspect is age. May...

One of the first things to suspect is age. May plants have juvenile stage in which they do not flower. Plants that are receiving to much nitrogen in either lawn food or naturally may not bloom. To...
Replies: 9
Views: 1,418
Posted By WeldGod

Welcome.......The circular saw and table saw will...

Welcome.......The circular saw and table saw will both work for the jobs you list. And I say you can never have to many saws. ;) You can get more precise cut with a table saw than with a circular...
09-04-05, 02:18 AM
Replies: 1
Views: 1,216
Posted By WeldGod

Talking Hi

We don't mind at all. We are glad to have you. Welcome aboard! ;)
09-04-05, 02:12 AM
Replies: 1
Views: 746
Posted By WeldGod

Covering the ground with a think layer of mulch...

Covering the ground with a think layer of mulch is is a good start. Protecting the plants from winds is also a good step to take. And if the climate is real cold where you are you may need to...
09-04-05, 01:46 AM
Replies: 1
Views: 998
Posted By WeldGod

I know this is not the answer you want but .........

I know this is not the answer you want but ...... maybe. If they are quality valves you are OK. If not quality valves they will last along time but eventually fail. Either way you are good for quite...
09-04-05, 01:38 AM
Replies: 5
Views: 11,561
Posted By WeldGod

Yes, you should be fine doing it that way. But...

Yes, you should be fine doing it that way. But make sure the soil used to fill in between walls is packed in all the way and fully filled in. If there is any gap between walls and the back wall...
Replies: 7
Views: 1,152
Posted By WeldGod

I would start by checking fuel supply and...

I would start by checking fuel supply and ignition. I would also have my engine codes read.
Replies: 6
Views: 2,352
Posted By WeldGod

If 1” tube is laid ou and welded right it should...

If 1” tube is laid ou and welded right it should be fine, if the cart will be used mostly on flat surfaces. But, if the vehicle is going to see any rough off road use you would need to use bigger.
Replies: 8
Views: 878
Posted By WeldGod

It came with a P5AD2-E Premium Motherboard. I do...

It came with a P5AD2-E Premium Motherboard. I do not have the driver CD and I do not have the box that I used the P5AD2-E to build. But, I would like to use it on another computer. It looks a lot...
Replies: 8
Views: 878
Posted By WeldGod

Dose any one know were I can find a driver for an Asus USB Camera?

Dose any one know were I can find a driver for an Asus USB Camera?
Replies: 13
Views: 1,038
Posted By WeldGod

Your current bandwidth reading is: 4.10 Mbps...

Your current bandwidth reading is:

4.10 Mbps

which means you can download at 524.29 KB/sec. from our servers.

28.8 kbps dial-up
33.6 kbps dial-up
53.3 kbps dial-up
56 kbps ISDN
Replies: 9
Views: 1,432
Posted By WeldGod

Below is a link to my walk through for putting a...

Below is a link to my walk through for putting a pic in your post.
Replies: 11
Views: 1,390
Posted By WeldGod

I have no experience with the Bosch hammer drill...

I have no experience with the Bosch hammer drill but, all of the other bosh tools I have used have been great.
Replies: 4
Views: 965
Posted By WeldGod

It could be a few things. The gates on the...

It could be a few things. The gates on the transmission could be not allowing it in to gear. It could also be hydraulic problems, a lot of times after working on the clutch this happens. Did you have...
Replies: 7
Views: 898
Posted By WeldGod

This link:Compression Test...

This link:Compression Test (www.pumaracing.co.uk/comp.htm) Will give you a good idea on how to start a compression test.
Replies: 7
Views: 898
Posted By WeldGod

Codes from the engine that tell the person...

Codes from the engine that tell the person working on it what the problem is. They will need some type of electronic scanner to get the codes from the Land Rover.
Replies: 7
Views: 898
Posted By WeldGod

It could be a ton of things. But I would start by...

It could be a ton of things. But I would start by having your codes read. Also if you had fluid shot in to your exhaust while it was hot it could be your converter making it hard for you engine to...
Replies: 4
Views: 965
Posted By WeldGod

Is the clutch working or dose it just grind when...

Is the clutch working or dose it just grind when you try to put it in gear?
Replies: 3
Views: 981
Posted By WeldGod

It could be a lot of things. It could be the...

It could be a lot of things. It could be the things that hogfan says so check those out. Dose it only happen in low range? But, with a 34 year old T-case it could be just time for a rebuild.
Replies: 2
Views: 1,018
Posted By WeldGod

With a manual transfer case it will not always...

With a manual transfer case it will not always shift easy, but it should shift in to 4-Hi if you try a few times. I would take it in for warranty work and tell them what it is doing to you. And don’t...
Showing results 1 to 25 of 200
 


 
Forum Jump