Search: Posts Made By: inoh1
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Replies: 8
Views: 11,711
Posted By inoh1

It runs like new again. Thanks!

It runs like new again. Thanks!
Replies: 8
Views: 11,711
Posted By inoh1

Everything was good except the metering lever...

Everything was good except the metering lever height. Fixed it. Now it starts and runs. Got the L set to be very responsive, however, I am bogging out when coming down from full throttle and...
Replies: 8
Views: 11,711
Posted By inoh1

I am having a similar issue. Feel like the...

I am having a similar issue. Feel like the carburetor is letting to much fuel in. I completely rebuilt the carburetor wt 657, removed jets, thoroughly cleaned, new gaskets and diaphragm, installed...
Replies: 14
Views: 1,481
Posted By inoh1

Top push rod is not on rocker arm. Not even in...

Top push rod is not on rocker arm. Not even in the valve. Why does it keep falling out?

Going to fish it out of the oil pan again.
Replies: 14
Views: 1,481
Posted By inoh1

OK Should I take the head gasket apart and make...

OK Should I take the head gasket apart and make sure the push rod is correct?
Replies: 14
Views: 1,481
Posted By inoh1

Displ:173 spec:xt173-0084

Displ:173
spec:xt173-0084
Replies: 14
Views: 1,481
Posted By inoh1

In that case, I am awaiting further instructions.

In that case, I am awaiting further instructions.
Replies: 14
Views: 1,481
Posted By inoh1

Finally got to work on it today. Crankshaft has...

Finally got to work on it today. Crankshaft has just one small dot on the gear. Camshaft has just one large dot on the gear. Did not see any IN or EX markings. A push rod and valve fell out while...
Replies: 14
Views: 1,481
Posted By inoh1

Kolher courage engine trouble

Hi

I am working on a Kolher Courage engine. Spec XT173-0084. Replace the oil pan because I thought it was cracked. Turns out the gasket was done for. The gears in the replacement oil pan would...
Replies: 15
Views: 1,975
Posted By inoh1

Cleaned carburetor as good as possible being that...

Cleaned carburetor as good as possible being that the two philips screws are seized. Will be replaced eventually. Plenty of nasty yellow stale gas came out. Then noticed plenty of compression but...
Replies: 15
Views: 1,975
Posted By inoh1

Update... Battery is good, starter is good. ...

Update...
Battery is good, starter is good. Mower wont start, possibly from stale fuel. Cleaned the spark plug. Checked to ignition coil with spark tester. All usual suspects seem good. ...
Replies: 15
Views: 1,975
Posted By inoh1

Finally got around to working on the mower today....

Finally got around to working on the mower today. Thanks for the brain kickstart. All Switches check out good. After tripple checking everything I noticed the battery wired backwards. Fixed it but...
Replies: 15
Views: 1,975
Posted By inoh1

Forgot to mention that I got 7 volts from the...

Forgot to mention that I got 7 volts from the battery. I have a little experience with wiring diagrams. So when I got a diagram from Sears that showed a different solenoid location I was confused. ...
Replies: 15
Views: 1,975
Posted By inoh1

Craftsman ride mower dead

Hello,

This is my first post here on these forums and I am looking for some advice.

I have a Craftsman riding mower Model #917.287210 with a B&S motor Model # 331877.

The problem is it does...
Showing results 1 to 14 of 14


 
Forum Jump