Search: Posts Made By: Gmaxx
Showing results 1 to 25 of 200
Search took 0.02 seconds.
Replies: 2
Views: 1,181
Posted By Gmaxx

Update: Here are a couple of pics so you can see...

Update: Here are a couple of pics so you can see the
location of the part that I need identified. It is connected
to C305

http://i29.photobucket.com/albums/c264/Genx65/Pana0236.jpg
...
Replies: 2
Views: 1,181
Posted By Gmaxx

Ge 27" tv

Hello,
I am currently working with a GE
model no. 27GT616 thatís using
an RCA CTC185AB3 chassis.
There is a burnt resistor that I am
unable to read the color code. The
resistor is R4306 (or...
Replies: 5
Views: 1,994
Posted By Gmaxx

Update: Found a bad cap (cv26) which is .47uF...

Update:
Found a bad cap (cv26) which is .47uF cap
connected between two pins of the main 56 pin IC chip.
I froze the cap and the bar went away. Actually it looks to
be a form of vertical fold...
Replies: 5
Views: 1,994
Posted By Gmaxx

Update: I noticed when I grab the black and...

Update:

I noticed when I grab the black and brown wires going to the back of the yoke (see pic below), the amount that the bar comes down the screen will change. These two wires go to the vertical...
Replies: 5
Views: 1,994
Posted By Gmaxx

Yes, I only used a solid background because it...

Yes,
I only used a solid background because it makes it easier to see in the pic. The blue background comes from the VCR that Im using when its turned on but have the tape on stop. Its a little like...
Replies: 5
Views: 1,994
Posted By Gmaxx

RCA TV (bar on screen)

I am working with an RCA model 32F530T TV.
The chassis number is ATC113-CD4.
Just replaced a flyback and got the unit running
however Iím noticing a bar at the top of the screen.
The bar is...
Replies: 4
Views: 1,686
Posted By Gmaxx

A new flyback and HOT got it running. Thanks

A new flyback and HOT got it running.

Thanks
Replies: 4
Views: 1,686
Posted By Gmaxx

Thanks for the reply, I'll see about getting a...

Thanks for the reply,
I'll see about getting a flyback.
Do you have any experience with ASTI or HR Diemen brand
replacement flybacks? Are they ok or no good?
Replies: 4
Views: 1,686
Posted By Gmaxx

RCA 32" TV (blows horizontal output)

I am working with an RCA model 32F530T TV.
The chassis number is ATC113-CD4.
The unit makes a constant chirp noise when plugged in.
I checked it out and found that the horizontal output ...
Replies: 2
Views: 897
Posted By Gmaxx

Thanks for the reply, Unless someone else...

Thanks for the reply,
Unless someone else chimes in with something concrete
I'll consider the set finished. I'll just have to alert the customer
that it may "initially" take a series of clicks of...
Replies: 2
Views: 897
Posted By Gmaxx

Toshiba 27" TV not starting correctly

Hello,
I am working with a Toshiba 27" TV model 27a34. I had to replace a zener diode in the chroma section and repair a burnt trace on the board to correct a horizontal width problem. I also had to...
Replies: 1
Views: 893
Posted By Gmaxx

One possibility would be a bad connection ...

One possibility would be a bad connection
someplace, maybe on a circuit board itself.
Many times they mount input and output
jacks directly to a circuit board. Sometimes
the solder joints can...
04-15-08, 02:26 PM
Replies: 9
Views: 5,897
Posted By Gmaxx

Check into Alpha 5, its much better than Access

Check into Alpha 5, its much better than Access
Replies: 6
Views: 21,359
Posted By Gmaxx

Do you know how to use a multimeter (or volt-ohm...

Do you know how to use a multimeter (or volt-ohm meter)?
Replies: 2
Views: 2,785
Posted By Gmaxx

Before going too far, Make sure youíre getting...

Before going too far,
Make sure youíre getting adequate water pressure to the inlet valve. In much of the line installations they use a shutoff (or piercing valve) that just straps across a cold...
Replies: 1
Views: 2,066
Posted By Gmaxx

If the motor itself is making unusual noises ...

If the motor itself is making unusual noises
it would have to be replaced.
Replies: 3
Views: 1,175
Posted By Gmaxx

Check on the bottom or side of the unit for a...

Check on the bottom or side of the unit for a small push in
circuit breaker or reset button.
Replies: 2
Views: 1,761
Posted By Gmaxx

Thatís always possible but before hoisting the...

Thatís always possible but before hoisting the blame on the pressure switch I would first check the hose assem that supplies pressure to it to begin with.
The pathway in the pressure switch hose...
Replies: 1
Views: 2,626
Posted By Gmaxx

Just my own opinion, If youíve had a lot of...

Just my own opinion,
If youíve had a lot of problems with it I would burry it and put that 210 bucks towards a different washer. I would do this before it starts cleaning out your wallet instead of...
Replies: 3
Views: 1,789
Posted By Gmaxx

The first thing you need to be checking before...

The first thing you need to be checking before going too far is
to see if you have 230 volts AC getting to the dryer. It could be missing this and still run but you wont get heat.
Replies: 2
Views: 2,498
Posted By Gmaxx

does it make that same noise when it turns on or...

does it make that same noise when it turns on or off? or is the noise youre hearing steady while the unit runs?
Replies: 6
Views: 9,821
Posted By Gmaxx

Sorry about that. One way to find out whether...

Sorry about that.
One way to find out whether your getting enough water is once its done filling up simply open the door then take a container with some hot water and add to whats already in the...
Replies: 1
Views: 1,053
Posted By Gmaxx

"Does anybody have the schematic for the motor...

"Does anybody have the schematic for the motor control board?"

Nope..the schematic for that board is more classified than the area 51 documents. You cant get the main chip either.Youre just going...
Replies: 1
Views: 1,011
Posted By Gmaxx

"could this be a bad element still? or something...

"could this be a bad element still? or something else?"

You should be getting 220 volts at the element. The first thing
you need to check is your source. Remove the cover where the
power cord...
Replies: 4
Views: 1,247
Posted By Gmaxx

Before you defrost anything take the freezer...

Before you defrost anything take the freezer panel off that covers the coils. Then make sure the unit is running and then very slowly turn the defrost timer clockwise
until the unit shuts off....
Showing results 1 to 25 of 200
 


 
Forum Jump