Search: Posts Made By: Torgue1
Showing results 1 to 20 of 20
Search took 0.01 seconds.
Replies: 5
Views: 8,723
Posted By Torgue1

Thank You all for your advice. I will rent a...

Thank You all for your advice. I will rent a hilty gun and attach the treated 2x6 to the wall using a barrier between the wall and the wood. Your advice is greatly appreciated. I have never run into...
Replies: 5
Views: 8,723
Posted By Torgue1

Need to attach wood 2x4 to poured concrete wall.

Torgue1,
I need some advice on mounting an electrical transfer device to a poured concrete wall. I have tried using mollies but drilling into this wall I keep hitting stones or something. I...
Replies: 2
Views: 1,651
Posted By Torgue1

Thank You Goldstar I will give what you suggest ...

Thank You Goldstar I will give what you suggest a try.
Replies: 2
Views: 1,651
Posted By Torgue1

Question Help on Snow blower starter cord/rope

hello I need help on starter cord for my snow blower. The cord broke when I pulled it to start the snow blower. I took the end pulley winder off of the unit and rethreated the cord thru the wind-up...
Replies: 2
Views: 1,604
Posted By Torgue1

Pulpo Thank you for answering my post . I am a...

Pulpo
Thank you for answering my post . I am a bit late in answering your suggestion I have been away. I will try to use the teflon tape I didn't see a O ring on the device. I will check that out...
Replies: 10
Views: 20,181
Posted By Torgue1

Gunguy45, I appreciate your advice and your...

Gunguy45,
I appreciate your advice and your response to my question. The epoxy plumbers fix I used is exactly the one you described comes in a tube and must be mixed to a uniform color and applied...
Replies: 10
Views: 20,181
Posted By Torgue1

Ecman51 Thank you for responding to my...

Ecman51
Thank you for responding to my question. I had a leak in a toilet sewer pipe beneath the flooring two years ago. The leak was small so i used the apoxy plumbers to stop it. Just recently I...
Replies: 2
Views: 1,604
Posted By Torgue1

Talking Sink drain stopper Rod.

I have always had a problem with leaking under a bathroom sink from the drain assembly to open and close the sink stopper. The rod and swivel ball assembly that raises the stopper in the sink and...
Replies: 10
Views: 20,181
Posted By Torgue1

Plumbers epoxy putty ? anyone have any comments pro or con need help

I have used this epoxy putty on a toilet 3" sewer pipe to plug a hole in the soldered joint iin this pipe. Would like some advise from someone who has had experince good or bad with this epoxy...
08-06-08, 06:46 PM
Replies: 4
Views: 2,348
Posted By Torgue1

HotinoOka Can I go over some of the areas and...

HotinoOka Can I go over some of the areas and apply more grout at this point ???
08-06-08, 06:28 PM
Replies: 4
Views: 2,348
Posted By Torgue1

THANK YOU FOR YOUR QUICK REPLY. The enhancer is...

THANK YOU FOR YOUR QUICK REPLY. The enhancer is put out by the same company that packaged the grout. It is a sand Grout. The enhanser is an anti fugus inhibitor. I am working downstairs and just...
08-06-08, 05:10 PM
Replies: 4
Views: 2,348
Posted By Torgue1

Grout Consistency

I Just mixed a batch of grout and it has the consistency of apple sauce.When mixing it the batter doesn't drip off the mixing stick. But I still feel it is two fluid. I mixed half of the 10lb of dry...
08-05-08, 07:26 AM
Replies: 35
Views: 5,403
Posted By Torgue1

To DSC3507 I have found alot of problems people...

To DSC3507 I have found alot of problems people have with with lighting and outlets is a neutral coming loose somewhere along the line. Checking the continuity of the neutral with an ohm meter to...
07-27-08, 03:11 PM
Replies: 35
Views: 5,403
Posted By Torgue1

Check the ground on the neutral the source...

Check the ground on the neutral the source neutral . Is there an indicator light on the GFI face? Is it lit? It sounds as if there is an open on the neutral of your source wires. Your neutral must be...
07-27-08, 02:36 PM
Replies: 6
Views: 33,751
Posted By Torgue1

I have filled in the gap in the seam with Henry...

I have filled in the gap in the seam with Henry 549 feather finish. I have other gouges in the plywood not many from where i removed the old tile and adhesive. I wanted to fill in these gouges with...
07-27-08, 02:23 PM
Replies: 6
Views: 33,751
Posted By Torgue1

Hi John The plywood is square cut it is 5/8" but...

Hi John The plywood is square cut it is 5/8" but there appears to be a subfloor below it. I could see the 3" copper pipe coming up to the flange thru plywood. I went down into my basement beneath...
07-26-08, 05:27 PM
Replies: 6
Views: 33,751
Posted By Torgue1

installing ceramic tile over old plywood subfloor

I am putting down ceramic tile on a bathroom floor. I stripped the bathroom of toilet and sink (no tub ) room is completely empty. I stripped the old tile from the plywood floor and removed the old...
07-26-08, 04:22 PM
Replies: 10
Views: 1,459
Posted By Torgue1

I am happy it worked out for you. smile John...

I am happy it worked out for you. smile John Nelson gave you the best advice ( switch Loop ) Good luck Double zero S picture is worth a thosand words.
07-26-08, 03:57 PM
Replies: 10
Views: 1,459
Posted By Torgue1

Double zero The switch looks right but the outlet...

Double zero The switch looks right but the outlet is wrong. The white wire is on the wrong terminal it is on the( load) terminal. Bring the white wire up to the( line) silver terminal it is on the...
07-26-08, 03:23 PM
Replies: 10
Views: 1,459
Posted By Torgue1

Smile Torque1, Looking at your photo the switch is to...

Torque1, Looking at your photo the switch is to the right and the out let to the left. The switch looks like it is wired with the black Hot wire on one side and a white neutral on the other side of...
Showing results 1 to 20 of 20


 
Forum Jump